曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 S 912-012-N00
 CAUTION: DURING THE REMOVAL OF THE PARTS THAT HAVE J THREADS, IDENTIFY
_______ THESE PARTS AND KEEP THESE PARTS TOGETHER. YOU CAN DAMAGE THE ENGINE, IF YOU INSTALL AN INCORRECT PART WHERE A J THREAD IS NECESSARY.
 (11) Nuts and bolts with J threads are used in many locations on the engine.
 (a)  The J threads have a full radius at the bottom on the threads and a larger minor diameter.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 70-20-03
 ALL  ú ú N01 Page 207 ú Oct 10/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
(b)  
The J threads have a longer life, better stressed extension property, and more tension strength.

 (c)  
Nuts and bolts with the J threads and nuts and bolts with the usual threads are the same when you look at them. 1) Nuts and bolts have part numbers to show that they have the

 J threads.
 NOTE: Nuts or bolts smaller than 0.200 inch (5.080 mm)
____ in the length by 0.050 inch (1.270 mm) in the width have no part numbers.
 2)  A blue dye is used on the nuts and bolts with the J thread at the first engine assembly.
 NOTE: The blue dye will burn off during the operation
____ of the engine or will go away when you clean the engine.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 70-20-03
 ALL  ú ú N01 Page 208 ú Oct 10/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
LOCKING METHODS - MAINTENANCE PRACTICES
_______________________________________
 1. General
_______
 A. This procedure gives the instructions for different lock devices.
 B. This procedure gives the data for the tasks that follow:
 (1)  
Cotter Pin Installation

 (2)  
Retaining Ring Installation

 (3)  
Tab Washer Installation

 (4)  
Cup Washer Installation

 (5)  
Lockwire Installation

 (6)  
Safety Cable Installation

 TASK 70-21-00-402-001-N00
 2. Cotter Pin Installation
_______________________
 A. Access
 (1)  Location Zone
 412 Engine No. 1
 422 Engine No. 2
 432 Engine No. 3
 442 Engine No. 4

 B. Procedure
 S 422-021-N00
 (1)  When you install a cotter pin in a nut, do these steps:
 (a)  
Tighten the nut until the torque is in the lower values of the range, unless a higher torque is specified. 1) Then tighten the nut until the slot aligns with the hole in

 the bolt shank.

 (b)  
If you get to the maximum torque before the slot and the hole align, assemble the nut again. 1) If you get to the maximum torque again, use a new nut.

 (c)  
If more than 50 percent of the cotter pin is above the castellation of the nut, install a new nut.

 (d)  
Make sure the head of the pin engages tightly in the slot of the nut.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 70-21-00
 ALL  ú ú N01 Page 201 ú Jun 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.

L-25172
TANGENT
MAKE SURE THE COTTER PIN HEAD IS SNUG AGAINST THE PIN SHANK. DO NOT BEND THE PIN HEAD.
MAXIMUM NORMAL
COTTER PIN/PIN INSTALLATION
L-25223
Cotter Pin Installation Figure 201
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 70-21-00
 ALL  ú ú N01 Page 202 ú Feb 10/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
(e)  
Make sure the axis through the eye of the cotter pin is perpendicular to the bolt shank (Fig. 201).
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 STANDARD PRACTICES - ENGINE(17)