70-42-04
 ALL  ú ú N01 Page 201 ú Oct 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
WHEN TO USE  P11-014A  <140` F (60` C) FLASH POINT SOLVENTS APPROVED FP11-005@, P11-005A@, OR P11-059 P11-042@, P11-058, P11-038, P11-039, P11-014, P11-032A@,  >140` F (60` C) FLASH POINT OR USE ON METALLICS P11-063 OR P11-064 P11-057, P11-062, P11-055, P11-056, 
FPI (LOCAL)  X  X 
GENERAL WIPE  X  X  X 
PRE-ADHESIVE BONDING  X  X 
PRE-PAINTING  X  X 

@ = VAPOR PRESSURE IS GREATER THAN 45MM HG
Solvents Approved for Use on Metallics
Figure 201

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 70-42-04
 ALL  ú ú N01 Page 202 ú Oct 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
H80754
MATERIAL DESCRIPTION OFSPEC NO. NON-METALLIC PART MATERIAL LAMINATED MOLDINGS FIBERGLASS STRUCTURES,PWA 410  P11-005@, P11-005A, P11-014A P11-058 OR P11-059 P11-038, P11-039, P11-014, P11-032@, FLASH POINT <140` F (60` C) USE ON NON-METALLICS SOLVENTS APPROVED FOR XX 
IMPREGNATED PWA 411 CLOTH, GLASS, EPOXY RESIN  XX 
FOAMING PWA 446 POLYURETHANE RESIN,  X 
FABRIC, AROMATICPWA 459 IMPREGNATED POLYAMIDE, EPOXY RESIN  XX 
LAMINATED STRUCTURES,PWA 460 FABRIC EPOXY RESIN MATRIX AROMATIC POLYAMIDE  XX 
PWA 479 MOLDING COMPOUND, POLYAMIDE, COMPOSITE  X X 
PWA 628 FOAM MOLDED POLYURETHANE  X 
QUALITY FLUOROHALOCARBON PLASTIC FILM, SPECIALPWA 36013  X 
TEFLON COATINGPWA 36014  X 
PWA 36051 CARBON FIBER REINFORCED COMPOSITE AIRFOILS,  X X 
PWA 36408 RESIN IMPREGNATED FIBERGLASS, POLYIMIDE FABRIC, CARBON FIBER AND  X X 
FABRIC, ALUMINUMPWA 36414 EPOXY RESIN IMPREGNATED BOROSILICATE GLASS FIBER,  X X 
FABRIC, FIBERGLASS, EPOXYPWA 36422 RESIN IMPREGNATED  X X 
PWA 36426 MOLDING COMPOUND, POLYETHERIMIDE COMPOSITE  X 
PWA 36442 FLUOROELASTOMER SHEET  X 
PWA 36509 PRIMER, POLYURETHANE  X 
EROSION RESISTANT COATING, POLYURETHANE,PWA 36510  X 
FLUOROELASTOMER COATINGPWA 36516  X 

@ = VAPOR PRESSURE IS GREATER THAN 45MM HG
Solvents Approved for Use on Non-Metallics
Figure 202

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 70-42-04
 ALL  ú ú N01 Page 203 ú Oct 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
H80756
CAUTION:_______ DO NOT PUT INTO SOLVENTS THOSE PART ASSEMBLIES THAT
 CONTAIN MATERIALS THAT ARE NOT METALLIC.  THE SOLVENTS CAN
 CAUSE DAMAGE TO THE PARTS.
 DO NOT USE SIZED CHEESECLOTH FOR DEGREASING PARTS.  SIZED
 CHEESECLOTH CONTAINS RESIN BINDERS THAT CAN DISSOLVE IN
 SOLVENTS AND CAUSE CONTAMINATION OF BOND SURFACES ON THE
 PARTS.
 USE DISPENSERS THAT SQUIRT OR POUR THE SOLVENT.  THIS WILL
 PREVENT REPEATED DIPPING OF THE CONTAMINATED WORK CLOTH

 INTO THE SOLVENT.
 (a)  Wipe part with clean, white, lint-free, unsized cheesecloth wetted with one of the solvents.
 NOTE: Wear clean cotten gloves to touch cleaned parts to be
____ bonded.
 1)  See Figure 201 for solvents approved for use on metallic parts.
 2)  See Figure 202 for solvents approved for use on non-metallic parts.
 (b)  Let the parts air dry.
 NOTE: Do not use compressed air to dry part before adhesive
____ bonding or painting; some compressed air may contain oil vapors.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 70-42-04
 ALL  ú ú N01 Page 204 ú Oct 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 ENGINE CONTAMINATION:  FIRE EXTINGUISHING AGENTS HYDRAULIC FLUID, OIL OR
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 STANDARD PRACTICES - ENGINE(47)