70-24-01
ALL ú ú N01 Page 202 ú Feb 10/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
(c) Tighten the nut in the direction of the packing.
NOTE:____ Tighten the nut until the packing is tightly against
the first lower thread of the fitting.
(d) Install the fitting in the boss.
(e) Tighten the fitting until the packing touches the boss.
NOTE:____ Make sure the nut turns with the fitting. When the
packing touches the boss, the torque necessary to turn
the fitting will increase.
CAUTION:_______MAKE SURE YOU CORRECTLY ALIGN THE ELBOWS. MAKE SURE THE TUBE ENDS ARE IN THE CENTER AT THE ELBOWS . MAKE SURE THE TUBE ENDS MOVE FREELY. INCORRECTLY ALIGNED TUBES OR TUBES THAT CANNOT MOVE FREELY CAN CAUSE DAMAGE TO THE SYSTEM.
(f) Tighten the fitting 1-1/2 turns while you hold the nut stable.
EXTERNAL THREADS OF FITTING
PACKING RETAINER
PACKING
ASSEMBLY OF POSITIONING TYPE THREADED FITTINGS
L-71051
Positioning Type Flexible Fitting Installation Figure 202
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
70-24-01
ALL ú ú N01 Page 203 ú Oct 10/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
(g) Turn the fitting to the correct position.
NOTE:____ Do not turn the fitting more than one turn to put it in the correct position.
(h) Hold the fitting and tighten the nut until until it touches the boss.
NOTE:____ Make sure not to go above the recommended torque value (AMM 70-23-00/201). Make sure the packing or the retainer for the packing is not pushed out between the nut and the boss.
(i) Install a lockwire on the nut.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
70-24-01
ALL ú ú N01 Page 204 ú Feb 10/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
CLAMPSHELL TYPE CLAMPS - MAINTENANCE PRACTICES
______________________________________________
1. General_______
A. This procedure gives the installation instructions for the clampshell type clamps used on the power plant pneumatic, oil, hydraulic, and fuel system tubes. No special instructions are necessary to remove the clampshell type clamps.
B. The usual clampshell clamp assembly has three parts: two clampshells which are the same and, for the applicable installation, a cushioned or an uncushioned clamp.
C. You must use the clampshell clamp assemblies with the unplated clampshells in the high vibration and high temperature (not more than 800°F [427°C]) environments to hold the fluid system tubes.
D. You must use the clampshell clamp assemblies with the cadmium plated clampshells with the aluminum tubes only. These clampshell clamp assemblies have a limit to 400°F (204°C) applications.
E. These clamp assemblies are made for long life, and to wear in the clamp and outer clampshell surfaces. If replacement is necessary, you must replace the full clamp assembly, although only one component part has worn.
TASK 70-24-02-402-001-N00
2. Install the Clampshell Type Clamp (Fig. 201)_________________________________
A. Access
(1) Location Zone
412 Engine 1
422 Engine 2
432 Engine 3
442 Engine 4
B. Procedure
S 422-002-N00
CAUTION:_______DO NOT INSTALL THE CLAMPSHELL ON THE BEND OF A TUBE. IF YOU INSTALL THE CLAMPSHELL ON A BEND, DAMAGE TO CLAMPSHELL CAN OCCUR.
(1) Put the clampshell clamp assembly on the tube at a location where the tube is straight and free of bends and damage.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
70-24-02
ALL ú ú N01 Page 201 ú Oct 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
TUBE (REF)
Clampshell Type Clamp Installation 中國航空網(wǎng) www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：747-400 AMM 飛機維護手冊 STANDARD PRACTICES - ENGINE(37)
