(2)
MTI 2825-4044 Bracket - "P" Flange Vibration Pick-up,
Mechanical Technology
(3)
MTI 5500-4001 Accelerometer - (2 required), Mechanical Technology
(4)
MTI 8218-5201 Cable - "A" Flange Vibration Pick up,
Mechanical Technology
(5)
MTI 8218-5202 Cable - "P" Flange Vibration Pick-up,
Mechanical Technology
(6)
MTI 8218-5203 Harness - N1 Breakout Cable, Mechanical Technology
(7)
MTI 8900-5036 Amplifier - Engine Jumper Cable,
Mechanical Technology
(8)
MTI 8000-4225 Amplifier - Charge, Mechanical Technology
(9)
MTI 8900-5034 Harness - Engine Interface Cable,
Mechanical Technology
(10)
MTI 8900-5035 Jumper - PBS, Mechanical Technology
(11)
MTI 7000-4133 Portable Balancing System - PBS-4100 (This
includes a Computer and Data Acquisition Unit (DAU)),
Mechanical Technology
(12)
PWA 76855 Pump - Hydraulic, (use with PWA 86302)
Pratt & Whitney
Commercial Products Division
400 Main Street
East Hartford, CT 06108 US
(13)
PWA 85306 Puller - (For Turbine Shaft Plug), Pratt & Whitney
(14)
PWA 86302 Bender - Hydraulic (Turbine Clip Crimping Tool),
(Optional to PWA 102335), Pratt & Whitney
(15)
PWA 102335 Bender - Mechanical (Optional to PWA 86302),
Pratt & Whitney
(16)
PWA 85234 Riveter - (Flaring Pliers, for Fan Weight Rivets),
Pratt & Whitney
(17)
ENGINES POST-PW-SB 72-385;
0.190-32 Jackscrews - 8 are necessary
C.
Consumable Materials
(1)
G00846 Pencil - Silver
(2)
D00504 Petrolatum - White
(3)
G00949 Ink
D.
References
(1)
AMM 71-00-00/201, Power Plant
(2)
AMM 71-00-00/501, Power Plant
(3)
AMM 71-11-04/201, Fan Cowl Panels
(4)
AMM 71-11-06/201, Core Cowl Panels
(5)
AMM 72-31-01/401, Inlet Cone
(6)
AMM 78-11-02/401, Turbine Exhaust Plug
(7)
AMM 78-31-00/201, Thrust Reverser System
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
72-31-00
ALL ú ú N01 Page 504 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
E. Access
(1)
Location Zone
412 Engine No. 1
422 Engine No. 2
432 Engine No. 3
442 Engine No. 4
F.
Prepare for the Trim Balance Procedure.
S 485-082-N00
(1) Do the steps that follow to install the accelerometers (See Figures
501 and 502):
WARNING: DO THE THRUST REVERSER DEACTIVATION PROCEDURE TO PREVENT
_______ THE OPERATION OF THE THRUST REVERSER. ACCIDENTAL OPERATION OF THE THRUST REVERSER CAN CAUSE INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT.
(a)
Do the deactivation procedure for the thrust reverser for ground maintenance (AMM 78-31-00/201).
(b)
Open the fan cowl panels (AMM 71-11-04/201).
NOTE: It is necessary to open the left and right fan cowl
____ panels if all other cowlings are opened.
(c) Open the core cowl panels (AMM 71-11-06/201).
WARNING: OBEY THE INSTRUCTIONS IN AMM 78-31-00 TO OPEN THE THRUST
_______ REVERSERS. IF YOU DO NOT OBEY THE INSTRUCTIONS, INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT.
(d)
Open the thrust reversers (AMM 78-31-00/201).
(e)
Install the MTI 2825-4045 bracket and the MTI 5500-4001 accelerometer assembly on Flange A.
(f)
Connect the Turbine Pick-up Jumper with a routing down, near the drain mast.
(g)
Install the MTI 2825-4044 bracket and the MTI 5500-4001 accelerometer assembly on Flange P at the 9 o'clock position.
NOTE: The recommended location for the "P" flange
____ accelerometer is the 9 o'clock position (Fig. 502). It is not always possible to install the accelerometer bracket at the 9 o'clock position if the engine has an oil system tubing modification. If you cannot install the "P" flange accelerometer bracket at the 9 o'clock position, install the bracket at the 1:30 o'clock position as shown in (Fig. 502). The pick-up bracket can be installed on the forward or rearward side of "P" flange.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 發動機 ENGINE 1(114)
