conditions 4) All other data that you think is important.

 (b)  
Do all of the hot section repairs that are necessary to make the engine serviceable.

 NOTE: The PW4000 Engine Manual has the specifications for what
____
 is serviceable.

 1)  Remove and disassemble the high pressure turbine rotors to do an analysis of the metal of the 1st- and 2nd-stage turbine blades.
 2)  Do all other inspections that you think are necessary to make all the parts serviceable.
 (c)  
You can disassemble the Diffuser and Combustor Group and the Low Pressure Turbine Assembly, but this is not necessary unless you find problems.

 (d)  
Do visual and borescope inspections in these areas and in the high and low pressure compressor groups.

 NOTE: This will make sure that there are no problems in the
____
 engine.

 S 416-070-N00
 (2)  Do this task: Put the Airplane Back to its Usual Condition.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 72-00-00
 ALL  ú ú N01 Page 626 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
No. 5 - Engine Overspeed Inspection
___________________________________
 TASK 72-00-00-206-071-N00
 5. Engine Overspeed Inspection (Fig. 604)
___________________________
 A. General
 (1)  This task gives you the steps to do after the speed of the low pressure rotor (N1) or the high pressure rotor (N2) goes above its redline.
 NOTE: When the speed of a rotor is above its redline, this
____
 condition is called overspeed.

 B. References
 (1)  
AMM 45-10-00/201, Central Maintenance Computer System

 (2)  
AMM 71-00-00/501, Power Plant

 (3)  
AMM 71-00-02/401, Power Plant

 (4)  
AMM 77-12-00/501, Engine Tachometer System

 C.
Access

 (1)  
Location Zone
 412 Engine 1
 422 Engine 2
 432 Engine 3
 442 Engine 4

 D.
Procedure

 S 286-072-N00
 (1)  
Find the speed and the length of time that N1 or N2 operated at above its redline:

 (a)  
Press the ENG EXCD switch on the EICAS maintenance panel (AMM 45-10-00/201).

 (b)  
Look at the ENG EXCD page to find the maximum speed of N1 and N2 and the length of time each rotor was above its redline.

 NOTE: The EICAS does not make an overspeed record for
____ the speed of N1 or N2 unless the speed of the rotor is more than 1.0% above its redline.
 No action is necessary for a N1 or N2 speed between its redline and redline transient that lasts for less than 5 seconds.
 (c)  If the ENG EXCD page shows that the speed of N1 or N2 did not go above its redline by more than 1.0% (112.5% for N1, 106.6% for N2), do the step that follows: 1) To calculate the correct length of time the speed of the
 rotor was above its redline, add 5 seconds to the time shown on the ENG EXCD page.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 72-00-00
 ALL  ú ú N01 Page 627 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES /MAINTENANCE MANUAL ////////////////////////
115
N REDLINE TRANSIENT 113
1
N REDLINE 111.4
1
ROTOR SPEED (PERCENT)

AREA C 
AREA B 
AREA A 
NO ACTION 
REQUIRED 
AREA C AREA B AREA A NO ACTION 
REQUIRED 

107
106.3 N REDLINE TRANSIENT
2
105.5 N REDLINE
2
100
100 LOW PRESSURE HIGH PRESSURE ROTOR NROTOR N
1 2
Rotor Overspeed Maintenance Actions
Figure 604

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 72-00-00
 ALL  ú ú N01 Page 628 ú Feb 18/00
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 發動機 ENGINE 1(36)