WARNING: OBEY THE INSTRUCTIONS IN AMM 78-31-00 WHEN YOU OPEN THE THRUST
_______ REVERSER. IF YOU DO NOT OBEY THE INSTRUCTIONS, INJURIES TO PERSONS OR DAMAGE TO EQUIPMENT CAN OCCUR.
(4) Open the right thrust reverser (AMM 78-31-00/201).
PACKING
GROOVE
PULLER
GROOVE
RETAINING SEAL
RING
B DETAIL CARBON
B GEARBOX MAIN
B-B
PACKING
FWD FUEL PUMP
PAD
B
PULLER PULLER
RING
L-A3550
Fuel Pump Drive Oil Seal Installation
Figure 401 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
72-61-06
ALL ú ú N01 Page 403 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
E. Procedure
S 024-019-N00
(1)
Do the steps that follow to remove the seal (Fig. 401).
(a)
Remove the fuel pump and the fuel metering unit (AMM 73-11-01/401).
(b)
Remove the retaining ring that attaches the seal to the fuel pump pad.
S 494-004-N00
(2)
Install PWA 85204 or PWA 88110 puller to the seal housing.
(a)
Engage the puller jaws in the puller groove on the seal housing.
(b)
Move the puller ring until the jaws are attached to the groove.
S 024-005-N00
(3) With a slide hammer motion of the puller, remove the oil seal from the drive pad of the fuel pump.
NOTE: This slide hammer motion makes a stronger force than the
____
preformed packing.
S 094-006-N00
(4)
Disengage the puller from the seal.
S 014-021-N00
(5)
Discard the preformed packing.
S 034-007-N00
(6)
Install a cover on the fuel drive pad on the main gearbox.
TASK 72-61-06-404-008-N00
3. Install the Fuel Pump Drive Oil Seal (Fig. 401)
____________________________________
A. Consumable Materials
(1)
D00390 Oil - Engine
B.
References
(1)
AMM 71-00-00/501, Power Plant
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
72-61-06
ALL ú ú N01 Page 404 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
(2)
AMM 71-11-04/201, Fan Cowl Panels
(3)
AMM 71-11-06/201, Core Cowl Panels
(4)
AMM 73-11-01/401, Fuel Pump
(5)
AMM 78-31-00/201 Thrust Reverser System
(6)
IPC 72-61-06 Fig. 1
C.
Access
(1)
Location Zone
412 Engine 1 - Main Gearbox Fwd Face 4 o'clock
422 Engine 2 - Main Gearbox Fwd Face 4 o'clock
432 Engine 3 - Main Gearbox Fwd Face 4 o'clock
442 Engine 4 - Main Gearbox Fwd Face 4 o'clock
(2)
Access Panel
416 Right Thrust Reverser Half - Engine 1
426 Right Thrust Reverser Half - Engine 2
436 Right Thrust Reverser Half - Engine 3
446 Right Thrust Reverser Half - Engine 4
D.
Prepare for the Installation
S 224-009-N00
(1) Make sure that the clearance between the face of the seal and the
bearing housing of the fuel pump is in the limits in the table that
follows.
~............................................................. | | | NEW PART REFERENCE | CLEARANCE | | | | DIMENSIONS | LIMITS | | PART | | INCHES | INCHES | | NAME | DIA | (MM) | (MM) | | | ............................................... | | | MIN | MAX | MIN | MAX | ............................................................... | SEAL | OD | 3.3570 | 3.3640 | | | | | | (85.268) | (85.501) | 0.0010 | 0.0092 | ......................................... (0.0260) | (0.2340) | | HOUSING | ID | 3.3650 | 3.3662 | | | | | | (85.471) | (85.501) | | | 2.........….....…...........…...........…..........…..........1 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：747-400 AMM 飛機維護手冊 發動機 ENGINE 2(136)
