72-62-01
ALL ú ú N01 Page 417 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
G22902
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
(i)
ENGINES POST-PW-SB 72-438; Make the tabs of the key washers (28B) flat to remove the key washers (28B) and and the bolts (28A) that attach the angle gearbox (11) to the intermediate case. 1) Discard the key washers (28B).
(j)
Remove the bolt (28D) and pin stop (28C) from each support bracket (27). 1) Discard the pin stop (28C).
(k)
Remove the angle gearbox with the PWA 101035 Jackscrew Puller:
1) Install the PWA 101035 Jackscrew Puller between the 5th-and 6th-stage strut of the intermediate case and attach the puller to the inner strut flanges with the four hex head cap screws.
2) Attach the PWA 101035 Jackscrew Puller arms to the support brackets (27) with the detail bolts (28D).
3) Move the two arm assemblies of the jackscrew puller to the outer position and tighten the two bolts to lock the arms in position.
4) Turn the large jackscrew nut to disengage the angle gearbox (11) from the intermediate case. 5) Lower the angle gearbox (11) and install it on the support stand. 6) Remove the four hex head cap screws that attach the PWA 101035 Jackscrew Puller to the inner strut flanges. 7) Remove the packing (18) from the top of the angle gearbox and discard. 8) If you will install a different angle gearbox, remove the support bracket (27) from each side of the angle gearbox. 9) Install covers on all open areas.
(l) Remove the angle gearbox with the PWA 87502 Knocker Puller (optional to the PWA 101035 Jackscrew Puller): 1) Attach the PWA 87502 Puller to the angle gearbox support
brackets (27) with the detail bolts (28D). 2) With the puller, loosen the angle gearbox (11) from the intermediate case. 3) Lower the angle gearbox (11) and install it on the support stand. 4) Remove the packing (18) from the top of the angle gearbox and discard. 5) If you will install a different angle gearbox, remove the support bracket (27) from each side of the angle gearbox. 6) Install covers on all open areas.
S 024-091-N00
(4)
Remove the horizontal drive shaft (20) and the housing (5) of the horizontal drive shaft from the main gearbox (Fig. 401).
(a)
Remove and discard the packing (23) from the rear groove in the housing (5) of the horizontal drive shaft.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
72-62-01
ALL ú ú N03 Page 418 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
TASK 72-62-01-404-034-N00
3. Install the Angle Gearbox
_________________________
A. Equipment
(1)
M303, M305 or M307 Bergen Mechanical Crimper Gergen Cable Technologies Inc 170 Gregg St
P.
O. Box 1300
Lodi, NJ 07644-9982
(2)
Puller - PWA 85518
(3)
Puller - PWA 85768
(4)
Puller - PWA 87502
(5)
Gage - Plug, PWA 87514
(6)
Crimper - Finish, PWA 87552
(7)
Crimper - Prebend, PWA 87553
B.
Consumable Materials
(1)
D00137 Lubricant - Engine Oil (PWA521B)
(2)
G00033 Cheesecloth - Unsized
(3)
G02334 Lockwire, (P05-289) 0.032 inch (0.813 mm) AS3214-02
(4)
G02335 Cable, Safety (P05-291)
(5)
G02332 Ferrule, Safety Cable (P05-292)
(6)
G00964 Compound - Antigalling, Fel Pro C-200
(7)
A00091 Sealant - Silicone, Rubber, Red (RTV 159)
(8)
A00482 Sealant - Silicone, Rubber, Gray (RTV 157)
(9)
B00130 Alcohol - Isopropyl
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
72-62-01
ALL ú ú N03 Page 419 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 發動機 ENGINE 2(173)
