EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
72-61-07
ALL ú ú N01 Page 404 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
D. Prepare for the Installation
S 224-009-N00
(1) Make sure the clearance between the EDP oil seal and the engine gearbox housing are within the limits given in the table.
~............................................................. | | | NEW PART REFERENCE | CLEARANCE | | | | DIMENSIONS | LIMITS | | PART | | INCHES | INCHES | | NAME | DIA | (MM) | (MM) | | | ............................................... | | | MIN | MAX | MIN | MAX | ............................................................... | SEAL | OD | 3.3570 | 3.3640 | | | | | | (85.268) | (85.445) | 0.0010 | 0.0092 | ......................................... (0.0260) | (0.2340) | | HOUSING | ID | 3.3650 | 3.3662 | | | | | | (85.471) | (85.501) | | | 2.........….....…...........…...........…..........…..........1
E. Procedure
S 424-021-N00
(1)
Do the steps that follow to install the EDP oil seal (Fig. 401):
(a)
Remove the dust cap from the engine gearbox.
(b)
Lubricate the new packing with engine oil. 1) Install the packing in the groove of the EDP oil seal.
(c)
Lubricate the mating (carbon) surface of the EDP oil seal with engine oil. 1) Install the EDP oil seal on the end of the gear shaft.
(d)
Install the retaining ring in the groove in the gearbox housing.
S 414-029-N00
(2) Install the EDP (AMM 29-11-05/401).
S 414-022-N00
WARNING: OBEY THE INSTRUCTIONS IN AMM 78-31-00 WHEN YOU CLOSE THE THRUST
_______ REVERSERS. IF YOU DO NOT OBEY THE INSTRUCTIONS, YOU CAN CAUSE INJURIES TO PERSONS OR DAMAGE TO EQUIPMENT.
(3) Close the right thrust reverser (AMM 78-31-00/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
72-61-07
ALL ú ú N01 Page 405 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
(4) S 414-023-N00Close the right core cowl panel (AMM 71-11-06/201).
(5) S 444-024-N00Do the activation procedure for the thrust reverser (AMM 78-31-00/201).
(6) S 414-026-N00Close the right fan cowl panel (AMM 71-11-04/201).
(7) S 714-025-N00Do the test for the accessory drive seals that is shown in the Power Plant Test Reference Table (AMM 71-00-00/501).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
72-61-07
ALL ú ú N01 Page 406 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
STARTER DRIVE COUPLING - REMOVAL/INSTALLATION
_____________________________________________
1. General
_______
A. This procedure gives the steps to remove and install the starter drive coupling.
B. This coupling is found on the aft side of the main gearbox at the 5 o'clock position.
C. You must open the thrust reverser halves and remove the starter to get access to the coupling.
TASK 72-61-09-004-001-N00
2. Remove the Starter Drive Coupling
_________________________________
A. Special Tools and Equipment
(1)
PWA 26377 - Holder, Pratt & Whitney, Commercial Products Division, 400 Main Street, East Hartford, CT 06108
(2)
PWA 85502 - Puller, Pratt & Whitney
B.
References
(1)
AMM 71-11-04/201, Fan Cowl Panels
(2)
AMM 71-11-06/201, Core Cowl Panels
(3)
AMM 78-31-00/201, Thrust Reverser System
(4)
AMM 80-11-01/401, Starter
(5)
IPC 72-61-03 Fig. 1
C.
Access
(1)
Location Zones
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 發動機 ENGINE 2(139)
