曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 |  5 | 0.049-0.051 (1.244-1.295) |
 ..........................................................
 |  6 | 0.099-0.101 (2.514-2.565) |
 2................….......................................1
 1)  Remove the screws from the trailing edges of the (front)
 liner segments and, if necessary, the fairing at Flange D.
 2) Clean the washers and the area around the bolt holes, with
 a clean cheese cloth that is moist with alcohol.
 a)  Dry the surfaces fully in air that is at ambient
 temperature, until there is no more alcohol on the
 parts.
 NOTE: There must be no alcohol on the parts when the
____
 sealant is applied.

 3)  Use screws to temporarily hold the washers in the correct position.
 (f)  Bond the washers to the (front) liner segments with a fillet of sealant (RTV 195 or RTV 197) all around.
 NOTE: It is permitted to have a very small quantity of sealant
____
 between the washer and the liner segment.

 (g)  Cure the sealant in in air that is at ambient temperature , for a minimum of two hours, until it is not tacky, before you touch it.
 S 424-010-N00
 (2)  
Install the liner segments as follows:

 (a)  
Lubricate the threads of the applicable screws with engine oil (Table 402).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 72-34-06
 ALL  ú ú N01 Page 406 ú Oct 10/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
Washer Thickness And Screw Lengths
 Table 402
 ~........................................................................
 | Screw PN | Screw Length | Washer Thickness | Quantity of Screws |
 ..........................................................................
 | 593111 | 0.495 - 0.505 | 0.000 - 0.015 | 0 - 43 As Necessary |
 ..........................................................................
 | ST1382-09 | 0.542 - 0.562 | 0.016 - 0.070 | 0 - 43 As Necessary |
 ..........................................................................
 | ST1382-10 | 0.594 - 0.625 | 0.071 - 0.130 | 0 - 43 As Necessary |
 ..........................................................................
 | ST1382-11 | 0.656 - 0.687 | 0.131 - 0.210 | 0 - 43 As Necessary |
 2...........…..................…..................…......................1
 (b)  
Attach the trailing edges of the liner segments to the fan exit case, with the lubricated screws.

 (c)  
Tighten all the screws to 36-40 pound inches (4.067-4.519 newton meters).

 (d)  
Clean the mating axial edges of the liner segments. 1) Make a clean piece of cheesecloth moist with alcohol. 2) With the moist cheesecloth, clean the axial edges of the

 liner segments and the areas where the sealant will touch. 3) Dry the cleaned areas in air, until there is no alcohol on the parts.

 (e)  
Apply sealant to the edges of the liner segment as follows: 1) Apply the sealant (RTV 157 or RTV 159) to the edges of the liner segment. 2) Cure the sealant in air that has a minimum relative humidity of 25%. 3) Cure the sealant for two hours, minimum, until it is not tacky, before you touch it.

 4)  If it is possible, cure the sealant for eight hours, total, before operation of the engine.
 E.  Put the Airplane Back to Its Usual Condition.
 S 414-011-N00
 WARNING: OBEY THE INSTRUCTIONS IN THE PROCEDURE TO CLOSE THE THRUST
_______ REVERSERS. IF YOU DO NOT OBEY THE INSTRUCTIONS, INJURIES TO PERSONS OR DAMAGE TO EQUIPMENT CAN OCCUR.
 (1)  
Close the thrust reversers (AMM 78-31-00/201).

 (2)  
Close the core cowl panels (AMM 71-11-06/201).

 (3)  
Close the fan cowl panels (AMM 71-11-04/201).

 S 414-012-N00
 S 414-013-N00
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 72-34-06
 ALL  ú ú N01 Page 407 ú Oct 10/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 發動機 ENGINE 2(84)