(h)  
Tighten the larger (center) adapter to 150-170 pound-inches (16.9-19.2 newton-meters).

 (i)  
Tighten the outer adapters to 110-120 pound-inches (12.4-13.6 newton-meters).

 F.  
Procedure

 S 424-045-N00
 (1)  Install the solenoid:
 (a)  
Remove the protection covers from the open line ends.

 (b)  
Put the solenoid in position on the intermediate case, with the two capped adapters on the top.

 NOTE: The mount lug on the solenoid must be to the rear of the
____ lugs on the intermediate case.
 (c)  Lubricate the threads of the bolts, which attach the solenoid, with engine oil.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ENGINES WITHOUT PHASE 3 CHANGES ú

 75-33-03
 ú ú N02 Page 405 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
(d)  
Attach the solenoid and bracket to the intermediate case with the bolts. 1) Tighten the bolts to 85-95 pound-inches (9.6-10.7

 newton-meters).

 (e)  
If it was necessary to loosen the bolt and nut which attach the accessory cooling tube to the bracket, tighten the bolt to 36-40 pound-inches (4.1-4.5 newton-meters).

 (f)  
Lubricate the threads of the center adapter with the antigalling compound.

 (g)  
Connect the 15th-stage air supply tube to the center adapter.

 1)  Hold the adapter and tighten the tube nut to 225-250 pound-inches (25.4-28.2 newton-meters).

 (h)  
Lubricate the threads of the two remaining adapters on the solenoid with engine oil.

 (i)  
Connect the two signal tubes to the adapters.

 1)  Hold the adapters and tighten the tube nuts to 270-300 pound-inches (30.5-33.9 newton-meters).

 (j)  
Safety the three tube nuts with lockwire or safety cable and safety cable ferrule.

 (k)  
Remove the protection caps from the EEC electrical connector and the receptacle on the solenoid.

 CAUTION: USE THE CORRECT ASSEMBLY PROCEDURE, AND TOOLS, FOR THE
_______ HARNESS CONNECTOR INSTALLATION (AMM 70-24-05/201). IF YOU USE THE INCORRECT ASSEMBLY PROCEDURE, OR TOOLS, A DAMAGED OR LOOSE CONNECTOR CAN OCCUR. A LOOSE CONNECTOR PERMITS VIBRATION, WHICH CAUSES THE CONTACTS TO WEAR AND DECREASES THE LIGHTNING PROTECTION.
 (l)  
Connect the EEC electrical connector to the receptacle on the solenoid (AMM 70-24-05/201).

 G.  
Return the Aircraft to Its Usual Condition.

 (1)
Install the No. 7 segment of the fan exit liner (AMM 72-34-03/401).

 S 414-021-N00
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ENGINES WITHOUT PHASE 3 CHANGES ú

 75-33-03
 ú ú N02 Page 406 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
S 414-040-N00
 WARNING: OBEY THE INSTRUCTIONS IN AMM 78-31-00/201 WHEN YOU CLOSE THE
_______ THRUST REVERSERS. IF YOU DO NOT OBEY THE INSTRUCTIONS, INJURIES TO PERSONS OR DAMAGE TO EQUIPMENT CAN OCCUR.
 (2)  
Close the left thrust reverser (AMM 78-31-00/201).

 S 414-035-N00

 (3)  
Close the left core cowl panel (AMM 71-11-06/201).

 S 414-036-N00

 (4)  
Close the left fan cowl panel (AMM 71-11-04/201).

 S 444-037-N00

 (5)  
Do the activation procedure for the thrust reverser (AMM 78-31-00/201).

 S 864-023-N00

 (6)  
For the applicable engine, remove the DO-NOT-CLOSE tag and close this circuit breaker as follows:

 (a)  P6 Main Power Distribution Panel
 1) 6F15 ENG 1 PERF SOL PWR A/APU ENG START

 or ENG 1 PERF SOL PWR A
 2) 6F16 ENG 1 PERF SOL PWR B
 3) 6E15 ENG 2 PERF SOL PWR A
 4) 6E16 ENG 2 PERF SOL PWR B
 5) 6D15 ENG 3 PERF SOL PWR A
 6) 6D16 ENG 3 PERF SOL PWR B
 7) 6C15 ENG 4 PERF SOL PWR A
 8) 6C16 ENG 4 PERF SOL PWR B

 S 714-024-N00
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 大氣 AIR 2(103)