曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 NOTE:____ If the measured and recorded dimension X is not
 available, retract the flap until the upstops on the ballscrew nut and the universal are 90 degrees away from each other. This is a nominal position.
 (r) (s)  To retract the inboard TE flap, turn the torque tubes at the angle gearboxes of the inboard and outboard transmission manually, or with an air motor.Turn the torque tube until you get the dimension X at each transmission that you measured and recorded before (View A, Fig. 401).
 NOTE:____ If the measured and recorded dimension X is not
 available, retract the flap until the upstops on the ballscrew nut and the universal at each transmission are
 90 degrees away from each other. position. This is a nominal
 (t)  Remove the harnesses that were installed to prevent damage to the transmission ball screws during the flap removal.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-02
 ALL  ú ú 01 Page 421 ú Jan 28/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757
MAINTENANCE MANUAL

 S 824-029
 (8) Adjust and do a test of the flap installation (AMM 27-51-02/501).
 NOTE: Steps to do the items that follow are included in the
____
 adjustment/test procedure:

 -Connect the lower pushrods to the aft flap
 -
Install the aft fairing for the outboard flap track

 -
Install the trunnion fairing for the main landing gear

 -
Install the trunnion fairing door for the main landing gear

 -Put the airplane back to its usual condition.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-02
 ALL  ú ú 01 Page 422 ú Jan 28/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757 MAINTENANCE MANUAL
 INBOARD TRAILING EDGE FLAP - ADJUSTMENT/TEST
____________________________________________
 1.  General
_______
 A.  This procedure contains the adjustment and test of the inboard trailing edge (TE) flap. The adjustment and test is done while the aft flap is attached to the main flap, with the flap carriages and aft flap linkages installed.
 B.  The rigging dimensions in this procedure represent rigging the flaps with the wings in the unloaded condition (without engines or fuel weight on the wings). That is the configuration that most closely resembles the in-flight deflection of the wing.
 C.  For a in-service airplane the flaps are usually rigged with the engines installed, on jacks or gears, and with fuel weight on the wings. Regardless of this difference, the rigging dimensions given in this procedure are still the target dimensions for the rigging of the airplane in any configuration.
 NOTE: If the best rigging dimension you can obtain is not within
____ the limit, refer to the tables in this procedure to find the limits for a particular airplane configuration.
 TASK 27-51-02-825-001
 2.  Adjustment for the Inboard Trailing Edge Flap
_____________________________________________
 A.  Equipment
 (1)  
Rigging Bars (from TE Flap Rigging Bar Set,
 B27030-125):

 (a)  
Inboard Flap Rigging Bar - B27030-126

 (b)  
Inboard Flap Rigging Bar - B27030-129

 (2)  
Door Locks, MLG - (Ref 32-00-15)

 (3)  
Rig Pins from Set B20003-XX (Ref 20-10-24)

 (a)  
TE2 - P/N B20003-4

 (b)  
TE3 - P/N B20003-4

 (4)  
Trailing Edge Flap Power Drive Unit Lock -B27008-1

 (5)  
Inboard Flap Torque Tube Clamp - B27055-3 (Part
 of Flap Torque Clamp Set, B27055-1)

 B.  
Consumable Materials

 (1)  
A00247 Sealant - BMS 5-95

 (2)  
C00259 Primer - BMS 10-11, Type 1

 (3)  
C00308 Corrosion Preventive Compound -MIL-C-11796, Class 3

 (4)  
D00013 Grease - MIL-G-23827

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(174)