F.S. FuselageStation102.72
432.84 Referto Note
NoteNote
NOTE: Applycorrosionretardant
compoundPiperP/N197508or
197509,withspringin extended F.S.
condition.Referto 91-00-00for 344.31
Listof ConsumableMaterials F.S. 27.38 F.S.
F.S.
332.50
162.80 F.S.
251.00
F.S.
373.37
r F.S.
F.S. 365.96
355.75
F.S.
F.S. I
160.20
78.76 F.S.
r-\
93.30
ElevatorSystemInstallation
Figure 401 Sheet(1of 2)
EFFECTIVITY: 040-999
Jan10/9027-30-00
PIPER AIRCRAFT
PA-42-720 (Advanced Trainer)
MAINTENANCE MANUAL
A. Elevator and Tab (continued)
ElevatorTrim
Cables Elevator Trim Pulleys
FuselageStation162.60 and 251.00 FuselageStation279.38
NOTE: Apply corrosion retardant
compound Piper P/N 197 508 or
197 509, with spring in extended
condition. Refer to 91-00-00 for
List of Consumable Materials
Fuselage Station 332.50
See Note
Elevator
Up Cable FuselageStation431.45
FuselageStation373.37
ElevatorSystemInstallation Figure 401 Sheet(2 of 2)
EFFECTIVITY:
040-999
27-3000 PAGE5
27-30-00 Jan 10/90
PIPER AIRCRAFT
PA-42-720 (Advanced Trainer)
MAINTENANCE MANUAL
A. Elevator and Tab (continued)
ELEVATORAND ELEVATOR TRIM TAB
A. 7°+ 1°-20
B. 30°+ 1°-0
° ° -0°
C. 12 + 1/2
° °
D. 20 + 1 -0
CABLE TENSIONS
ELEVATOR=55 LBS ± 5 LBS. -NOTE -TRIM TAB TRAVEL WITH ELEVATORIN
ELEVATORTRIM = 14 LBS. + 2 LBS. NEUTRAL POSITION
CHORD LINE LEVEL (NEUTRAL POSITION) D
-NOTES-
1.TRIM TAB NEUTRAL POSITION IS TAB TRAILINGEDGEEVEN WITH THE TRAILING EDGEOF THE ELEVATOR, OR ITS NEUTRAL POSITION.
2. TRIM TAB FREE PLAY MUST NOT EXCEED
0.126MAX. AT THE TRAILING EDGE OF THE TAB.
3. RIG ELEVATORS WITH ELEVATORS IN NEUTRAL POSITION (PINNED AT AFT SECTOR). VERIFY THAT RIGHT HAND ELEVATORTRAILING EDGE IS ALIGNED WITH LEFT HAND ELEVATOR TRAILING EDGE. ADJUST LENGTH OF ANTI-SERVO RODS TO OBTAIN 0.12" ± 0.12" TRAILING EDGE UP OF THE RIGHT HAND TAB AS MEASURED ON THE INBOARD TRAILING EDGEOF THE TAB.
Elevator and Elevator Trim -Travels and Cable Tensions
Figure 501
EFFECTIVITY: 040-999
Feb 1/98 27-3000
PIPERAIRCRAFT
PA-42-720(Advanced Trainer)
MAINTENANCEMANUAL
A. Elevatorand Tab (continued)
Tool P/N 72046
ElevatorRiggingTool
Figure 502
ElevatorHorn Assembly
ElevatorTorque TubeCollar
VIEW A-A
ElevatorRiggingStops
Figure503
EFFECTIVITY: 040-999
27-30-00 PAGE
Jan 10/90
PIPER AIRCRAFT
PA42-720(Advanced Trainer)
MAINTENANCE MANUAL
A. Elevatorand Tab (continued)
7. Removalof Elevator PushTube (Figure 401)
(a) Removebullet, aft access plates on tail and vertical stabilizer, and bullet assembly on top of verticalstabilizer.
(b)After removing bullet assembly fromtop of vertical stabilizer,block or tie control horn so elevator remains in most upwardpositionwhentube is releasedfrom sector.
(c)
Withelevatorin most upward position, tubeand connecting arm on aft sector must protrude through slot on bulkhead to which the sector is attached. Reach through aft access hole in tail and disconnect tube from sector by removing AN4-13Abolt.
(d)
Removerestraint from control horn. Allow elevator tomove to down stop.
(e)
With elevator in down position, tubeconnectionto control arm is now accessible. Disconnect tube from elevator horn and pull out of tail.
(f)
Disconnectelevator down spring and apply retardantwithspring in extended position.(Refer to Lubrication Chart in 12-20-00 for corrosion retardantsused on elevator down spring.)
8. InstallationofElevator Push Tube (Figure 401)
(a)
Connectelevatordown spring.
(b)
With elevator in down position, tube connection to control arm is now accessible, insert into tail. Connecttubeto elevator horn.
(c)
Installrestraintto control horn. Move elevator to most upward position.
(d)
With elevator in most upward position, tube and connecting arm on aft sector must protrude through slot on bulkhead to which the sector is to be attached. Reach through aft access hole in tail and connect tubeto sector by installingAN4-13Abolt.
(e)
Remove restraint from control hom. Allow elevatorto move to down stop.
(f)
Installbullet, aft access platesontail and vertical stabilizer, and bullet assemblyontop of verticalstabilizer.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：夏延飛機維護手冊 Cheyenne IIIA PA-42-720 AMM 1(111)
