(b)
At leftflap,disconnectpositionsenderrodby removingcotterpinfromforwardendof rod.
(c)
Disconnectflap controltubesat flap. Donot rotatecontroltubesunlessto adjustflap.
(d)
Removeupperrollerassembliesfromflap brackets.
(e)
Removelowerrollerassembliesandremoveflap.
3. Installationof Flap
(a)
Placeflapinposition.Installlowerrollerassembliesonflapbracketsandtorquebolts.
(b)
Installupperrollerassembliesandtorquebolts.
NOTE: Withall rollersinstalled,but no actuatorhook-up,flapmustfreefall (dropfromits own
°
weight),withoutbinding,throughits normalrange(0 ° to 30 down)fromanypointin
this range.
(c)
Connectcontroltube.
(d)
If leftflapwas removed,connectpositionsenderrod.
(e)
Checkflapfor properoperation,riggingandadjustment.
EFFECTIVITY: 040-999 PAGE1
27-50-00 Jan
Jan 10/90
PIPER AIRCRAFT
PA-42-720 (Advanced Trainer)
MAINTENANCEMANUAL
A. Flaps (continued)
- FWD VIEW B
DOWN FWD- UP LIMIT SWITCH
VIEW C
A A VIEWD
A
B
C D
Wing Flap Installation Figure 401
EFFECTIVITY: 040-999
Jan 10/9027-50-00
PIPERAIRCRAFT
PA-42-720(Advanced Trainer)
MAINTENANCEMANUAL
A. Flaps (continued)
Removal of Flap Actuator Motor (Figure 402)
(a)
Removecenterfloor panel in main cabin area. Theflap actuator motoris located on forward sideof bulkhead station 174.00.
(b)
Disconnect electrical leadsfrommotor.
(c)
Cutsafety wire and disconnect flexibledrive shaft ends from motor.
(d)
Removeclampholding motor unitsmounting bracket. Remove motor.
(e)
Replaceshockgrommetsfrom bulkhead by removing motorwith mountingbracket from bulkhead.
5. Installation of Flap Actuator Motor (Figure 402)
(a)
Install shock grommetsin bulkhead at F.S. 174.00.
(b)
Install flap actuator motorand bracket,if previously removed,on forward sideof bulkhead. Ensureanti-rotationpin on motor fits in mounting bracket pinhole. Secureholdingclamp.
(c)
Connectflexible drive shaft endsto motor, attachnut finger tight, and secure with MS20995-C41 safety wire.
(d)
Connect electrical leads.
(e)
Check flap rigging and adjustments (Figure 502).
(f)
Install access plates and panels.
6. Removal of Flexible ActuatorShaft (Figure 402)
(a)
Removethe center floor panellocated in the main cabin area.
(b)
Removethe right or left row of seatsand floor panels aft of the main spar.
(c)
Removethe aft access plate on the fairing locatedon the underside between the fuselageand wing.
(d)
Removethe accessplates at the aft side of the wheel well at wing stations 40.00,47.00, and 56.00,on the undersideof the wing at W.S. 34.50, 42.50, 82.75 and 92.50, and on the false sparat W.S. 42.50, 53.00, 92.50 and 101.00.
(e)
Cutthe safety wire and disconnect the shaft fromthe actuator motorandflap transmission.
(f)
Removethe support clampon the fuselage bulkheadandthe support grommetswithinthe wing andfuselage.
(g)
Removethe actuator shaft.
7. Installationof Flexible Actuator Shaft (Figure 402)
(a)
Draw the shaft through the wing intothe fuselage.
(b)
Connectthe flexible drive shafts to the transmissions. Ensurethat the splines are properly engagedand run the shaft attaching nutson finger tight. Safety the nutswith MS20995-C41 safetywire.
(c)
Checkthe flap rigging and adjustments.
(d)
Installthe accessplates,panels,clamps, grommets, and seats.
EFFECTIVITY:
040-999 27-50-00 PAGE3 27-50-00 Jan 10/90
PIPERAIRCRAFT
PA-42-720(Advanced Trainer)
MAINTENANCEMANUAL
A. Flaps (continued)
Down Lmit Switch
Potentiometer
Linkage AmplifierAdjustment and Test Points
Control Potentiometer
Flap System FunctionalDiagram
Figure 1
EFFECTIVITY:
040-999
PAGE 4 27-50-00
Jan10/90
PIPERAIRCRAFT
PA-42-720 (Advanced Trainer)
MAINTENANCEMANUAL
A. Flaps (continued)
Right Transmission Shaft Assembly
Assembly
Selector Switch
Indicator, Flap Position
Motor LeftTransmission Assembly Postion Sender
Assembly
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：夏延飛機(jī)維護(hù)手冊 Cheyenne IIIA PA-42-720 AMM 1(117)
