(2)
Make sure that the Gaussmeter operates correctly:
-the pointer must move when you put the instrument near the shaft of the windshield wiper motors.
(3)
With the Gaussmeter, find the magnetic zones of the external parts of the frames of the windshield and sliding windows. Record the value for each zone.
NOTE : Ignore the magnetization on the shaft of the windshield wiper
____
motors.
Subtask 05-54-00-869-050
B. Demagnetize:
(1)
Obey the instructions from the manufacturer for the DEMAGNETIZER -110V/60HZ (DM05275A) or the DEMAGNETIZER - 220V/50HZ (DM05275B).
(2)
Energize the demagnetizer.
(3)
Put the demagnetizer at a very small distance (1 cm approx.) from the part it is necessary to demagnetize. This position gives the reference plane.
(4)
Push the power supply button (indicator light on) and keep the demagnetizer above the magnetic zone during 2 to 3 seconds. Then move the demagnetizer away slowly at a constant speed and at right angles to the reference plane. You must move the demagnetizer to a minimum distance of 50 cm approx. before you release the button.
(5)
Do the step (4) again for each zone that you must demagnetize.
(6)
De-energize the demagnetizer.
(7)
For each demagnetized zone, read the value shown on the Gaussmeter. Make sure that this value is near zero.
(8)
If you find zones that are not fully demagnetized, do again the step
(4) until the value read on the Gaussmeter is near zero.
5. Close-up
________ Subtask 05-54-00-410-050
A. Installation of the Standby Compass
(1) Install the standby compass (Ref. TASK 34-22-23-400-001). Subtask 05-54-00-730-050
B. Compensation of the Standby Compass
(1) Do the compensation of the standby compass (Ref. TASK 34-22-00-730-001).
LEVELING AND MEASUREMENT AFTER A/C ABNORMAL OPERATION - INSPECTION/CHECK
________________________________________________________________________
TASK 05-56-00-200-001
Inspection/Check of the Leveling and Measurement after Abnormal Operation of the Aircraft
1. Reason for the Job
__________________
This topic gives the instructions for the leveling, measurement and
alignment operations of the aircraft.
You can compare these checks with subsequent measurements to find possible
structural deformations after hard landings, too much turbulence, etc.
Do these checks after the replacement or major repair of a part of the
structure.
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific access platform 1.65 m (5 ft. 5 in.)
No specific access platform 11.91 m (39 ft. 1 in.)
No specific access platform 3.55 m (11 ft. 8 in.)
98A08001004000 1 SET - PLUMBS BOBS
98A08001005000 1 HOLDING SET - MEASURING CORD
98A08001006000 1 COLUMN-GRADUATED
98D08003000000 1 SET-PLUMB BOBS MLG NLG WHEELS
98D08103000000 1 LANDING GEAR WHEEL TOE-IN LINE BAR
98D08103000001 1 LANDING GEAR WHEEL TOE-IN LINE BAR
R 98D08103000002 1 LANDING GEAR WHEEL TOE-IN LINE BAR 98D08103500000 1 SIGHTING RODS SET 98D08103501000 1 PLUMB LINE PYLON
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R 07-11-00-581-001 Lifting for Aircraft Maintenance Operations 07-11-00-586-002 Lowering of the Aircraft for Maintenance Operations 28-25-00-650-001 Pressure Defuel **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
05-56-00-991-001 **ON A/C 301-399, Fig. 601
R 05-56-00-991-001-A Fig. 601A **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
05-56-00-991-002 **ON A/C 301-399, Fig. 602
05-56-00-991-002-A Fig. 602A **ON A/C 001-049, 051-099, 101-149, 201-299,
R 05-56-00-991-003 Fig. 603 **ON A/C 151-199, 401-499,
05-56-00-991-003-A **ON A/C 301-399, Fig. 603A
05-56-00-991-003-B Fig. 603B
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護(hù)手冊 AMM 時間限制/維護(hù)檢查 2(168)
