(Ref. Fig. 604/TASK 05-56-00-991-005)
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 05-56-00Page 607 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1

 Datum
 Figure 601/TASK 05-56-00-991-001

R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 05-56-00Page 608 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1

R  Datum 
R  Figure 601A/TASK 05-56-00-991-001-A 
R 1EFF :  301-399,  1  05-56-00 Page 609 
1  1  May 01/04
 1  1
 1CES  1

 Position of the Datum Points on the Fuselage
 Figure 602/TASK 05-56-00-991-002

R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 05-56-00Page 610 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1R Position of the Datum Points on the Fuselage R Figure 602A/TASK 05-56-00-991-002-A

R 1EFF : 301-399, 1 05-56-00Page 611 1 1 May 01/04 1 1 1CES 1

 Table 1 (Dimensions in Millimeters / Inches)
 Figure 603/TASK 05-56-00-991-003

R 1EFF : 001-049, 051-099, 101-149, 201-299, 1 05-56-00Page 612 1 1 May 01/05 1 1 1CES 1

 Table 1 (dimensions in Millimeters / Inches)
 Figure 603A/TASK 05-56-00-991-003-A

R 1EFF : 151-199, 401-499, 1 05-56-00Page 613 1 1 Aug 01/05 1 1 1CES 1R Table 1 (Dimensions in Millimeters / Inches) R Figure 603B/TASK 05-56-00-991-003-B

R 1EFF : 301-399, 1 05-56-00Page 614 1 1 May 01/04 1 1 1CES 1

 Table 2 (Dimensions in Millimeters / Inches)
 Figure 604/TASK 05-56-00-991-005

R 1EFF : 001-049, 051-099, 101-149, 201-299, 1 05-56-00Page 615 1 1 May 01/05 1 1 1CES 1R **ON A/C 151-199, 401-499,

 (Ref. Fig. 604A/TASK 05-56-00-991-005-A)
 **ON A/C 301-399,

 Subtask 05-56-00-941-053-A
 E. Datum Lines and Datum Points Necessary for the Measurements
 (1)
 Datum lines
 (Ref. Fig. 601A/TASK 05-56-00-991-001-A)

 (a)
 Longitudinal axis XX' = the line through the points 11A and 12 along the horizontal datum line of the fuselage point 22R, Z = 0.

 (b)
 Vertical axis ZZ' = the vertical line through the point 11A.

 (c)
 Transversal axis YY' = perpendicular to XX' and ZZ'.

 (2)
 Datum points of the fuselage
 (Ref. Fig. 602A/TASK 05-56-00-991-002-A)

 (3)
 Table of measurements

 (a)
 Table 1 (Ref. Fig. 603B/TASK 05-56-00-991-003-B)

 (b)
 Table 2 (Ref. Fig. 604B/TASK 05-56-00-991-005-B)

 **ON A/C ALL
 Subtask 05-56-00-941-054
 F. Procedure for the Z Measurements on Different Points of the Aircraft NOTE : Do the Z measurements with the COLUMN-GRADUATED (98A08001006000).
____
 (1) Operation of the column
 (a) The column is installed on a tripod. It is set in the vertical plane with a level.

 Table 2 (Dimensions in Millimeters / Inches)
 Figure 604A/TASK 05-56-00-991-005-A

R 1EFF : 151-199, 401-499, 1 05-56-00Page 617 1 1 Aug 01/05 1 1 1CES 1R Table 2 (Dimensions in Millimeters / Inches) R Figure 604B/TASK 05-56-00-991-005-B

R 1EFF : 301-399, 1 05-56-00Page 618 1 1 May 01/04 1 1 1CES 1

 (b)
 Use the thermometer installed on the column to measure the ambient temperature.

 (c)
 Adjust the height of the column with a rack system to align it with the Z datum of the aircraft.

 4. Procedure
_________

R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
 Subtask 05-56-00-220-050
 A. Position of the Bottom Fuselage Points in the X, Y and Z Axes (Ref. Fig. 605/TASK 05-56-00-991-007, 606/TASK 05-56-00-991-008)
 NOTE : For the check of the point 10, measure the radome.
____
 (1) Datum lines
 (a)
 Make a projection of the points 10, 11, 12 and 13 to the floor with the SET - PLUMBS BOBS (98A08001004000).

 (b)
 Move the points 11 and 12 to the left by the dimension Y = 47.36 mm (1.8645 in.).

 NOTE : The dimension 47.36 mm (1.8645 in.) at the points 11 and
____ 12 is due to the angular position of the tool. You only use this dimension when you measure with the SIGHTING RODS SET (98D08103500000) installed on these points. (Ref. Fig. 606/TASK 05-56-00-991-008)
 (c)
 Move the points 10 and 13 to the left by the dimension Y = 45 mm (1.7716 in.).

 (d)
 Align a cord through the points 11 and 12 with the HOLDING SET -MEASURING CORD (98A08001005000).

 (2)
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM 時間限制/維護(hù)檢查 2(170)