EFF : ALL
11-00-00Page 201
May 01/05
CES
R C. Referenced Information
R -------------------------------------------------------------------------------
R REFERENCE DESIGNATION
R -------------------------------------------------------------------------------
R 51-75-12-300-003 Repair of Minor Paint Damage (Topcoat Only)
R 3. Job Set-up__________
R Subtask 11-00-00-941-056
R A. Get Access
R (1) Get access to the area where you must remove the decal.
R 4. Procedure_________
R Subtask 11-00-00-120-055
R A. Stripping
R (1) Apply masking tape or masking paper on the area adjacent to the decal
R location.
R (2) Rub the marking surface with MISCELLANEOUS (Material No. 19-011) to
R remove the warnish.
R (3) Rub the marking surface with abrasive cloth, grade 240.
R (4) Clean the rubbed area with MISCELLANEOUS (Material No. 19-003).
R Subtask 11-00-00-370-053
R B. Painting
R (1) Apply paint where necessary (Ref. TASK 51-75-12-300-003).
R 5. Close-up________
R Subtask 11-00-00-942-068
R A. Make sure that the work area is clean and clear of tool(s) and other
R items.
EFF : ALL
11-00-00Page 202
May 01/05
CES
TASK 11-00-00-400-002
Installation of the Decals
1. Reason for the Job__________________
Self Explanatory
2. Job Set-up Information______________________
R A. Fixtures, Tools, Test and Support Equipment
R R R -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
R R R R No specific No specific No specific No specific cutter scissors spare blades Couppy cutter
R B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R 11-00-00-991-001 11-00-00-991-007 Fig. 201 Fig. 202
3. Job Set-up__________
Subtask 11-00-00-110-061
A. Not Applicable
4. Procedure_________
Subtask 11-00-00-915-050
A. Application to Even or Irregular Surface (Ref. Fig. 201/TASK 11-00-00-991-001)
CAUTION : DO NOT USE A METAL SCRAPER TO REMOVE THE UNWANTED MATERIAL. A
_______ METAL SCRAPER CAN CAUSE DAMAGE TO THE SURFACE OF THE COMPONENT.
EFF : ALL
11-00-00Page 203
Aug 01/05
CES
R Installation of Decals Figure 201/TASK 11-00-00-991-001
EFF : ALL 11-00-00 Page 204 Aug 01/05
CES
R R R R R R NOTE : To prevent scribe marks on the aircraft skin, use scissors or a____ cutter with a plate between the film and the aircraft skin (0.6 mm (0.0236 in.) thick minimum with metal and 2 mm (0.0787 in.) thick minimum with hard plastic). You can also use a Couppy cutter or spare blades. (Ref. Fig. 202/TASK 11-00-00-991-007)
(1) Decals applied over a joint between two surfaces which move with respect to each other.
(a) With gaps of 2.53 mm (0.0996 in.) and greater, cut the decal at the center of the gap and wrap the decal around both edges. See Method A.
(b) With gaps of less than 2.53 mm (0.0996 in.), cut the decal flush with the front or upper edge of the joint and wrap the decal around the rear or lower edge. See Method B.
(2) Decals applied across lap joints.
R (a) The decal, when it is applied, is wrapped smoothly and continuously around the edge of the lap joint. See Method C (preferred method).
(3) Decals applied to exterior emergency exit handles. See Method E.
(a) Before removing the backing paper, place the decal on the handle and slit the decal overlap around each rounded corner.
(b) Remove the backing paper and apply the decal, pressing the overlap around the edges of the handle.
(4) Cut decals, except pressure sensitive Polyester, around the heads of fasteners on removable panels and punch the decal into the recessed slot. Cut and remove an area of film of pressure-sensitive polyester decals the approximate size of a protruding-head rivet or fastener. Allow the adhesive to cure for 1/2 hour before sealing the edges.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM PLACARDS AND MARKINGS(14)
