EFF : ALL
11-00-00Page 205
Aug 01/05
CES
R R Decal Cutting Procedure Figure 202/TASK 11-00-00-991-007
EFF : ALL 11-00-00 Page 206 Aug 01/05
CES
TASK 11-00-00-400-003 Installation of the Self-Adhesive Placards Affixed to Plexiglas
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-002 USA MIL-PRF-680 DRY CLEANING SOLVENT (VARSOL/WHITE SPIRIT) (Ref. 20-31-00)
3. Job Set-up
__________ Subtask 11-00-00-110-050
A. Cleaning
(1) Clean and degrease the Plexiglas surface to which the placard is to be affixed, using CLEANING AGENTS (Material No. 11-002) then thoroughly dry out.
NOTE : Any drilling of holes or trimming of the placard required
____
shall be performed prior to installation.
4. Procedure
_________ Subtask 11-00-00-915-051
A. Installation of Labels
(1)
Starting at one end peel off the protective backing paper over 10 mm (0.3937 in.) approx. and fold back.
(2)
Affix the peeled end to the Plexiglas and gradually remove the backing paper while pressing the placard down onto the Plexiglas.
EFF : ALL
11-00-00Page 207
Aug 01/05
R
CES
(3) Carefully smooth out the placard working from the center outwards. NOTE : Do not soil the adhesive contact surface of the placard, do
____ not touch this surface with your fingers.
5. Close-up
________ Subtask 11-00-00-942-052
A. Make sure that the work area is clean and clear of tool(s) and other items.
EFF : ALL
11-00-00Page 208
Aug 01/05
R
CES TASK 11-00-00-400-001
Installation of the Identification Tapes on Metal Lines
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-003 USA ASTM D 740 METHYL-ETHYL-KETONE (Ref. 20-31-00)
Material No. 11-004 USA MIL-T-81533 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM) (Ref. 20-31-00)
Material No. 11-016 USA BOEING BAC 5000 BAC 5504 BAC 5750 CLEANING SOLVENT (Ref. 20-31-00) Material No. 16-003 F ASNB70720 COATING (OBSOLETE USE 16-021) (Ref. 20-31-00) Material No. 16-016 C Z-12.383 EXTERNAL DECORATION PAINT (Ref. 20-31-00)
3. Job Set-up
__________
Subtask 11-00-00-110-051
A. Cleaning
(1)
Make sure that the tape is approximately 5 mm (0.1968 in.) longer than the circumference of the metal line.
(2)
Clean the surface on which you will bond the tape, using CLEANING AGENTS (Material No. 11-004) or alternatively CLEANING AGENTS (Material No. 11-003) or CLEANING AGENTS (Material No. 11-016), then thoroughly dry out.
EFF : ALL
11-00-00Page 209
Aug 01/05
R
CES
4. Procedure
_________
Subtask 11-00-00-915-052
A. Installation of Identification Tapes
(1)
Remove the backing paper.
(2)
Affix the tape by evenly unrolling and gradually smoothing out to prevent the formation of air bubbles.
(3)
Overlap the tape ends and smooth out.
(4)
Apply two coats of STRUCTURE PAINTS (Material No. 16-003) to the band, overlapping the edge of the band by 10 mm (0.3937 in.) approx. using a soft hair brush.
(5)
If the paint becomes damaged, apply STRUCTURE PAINTS (Material No. 16-016) to prevent attack of the adhesive by fluid (e.g. against hydraulic fluid) and subsequent separation of the tape.
(6)
If the film of STRUCTURE PAINTS (Material No. 16-003) is excessively damaged, replace the tape and renew the protective finish.
5. Close-up
________ Subtask 11-00-00-942-059
A. Make sure that the work area is clean and clear of tool(s) and other items.
EFF : ALL
