11-00-00Page 227
May 01/05
R
 CES  TASK 11-00-00-400-012

 Installation of the Labels on Landing Gear
 1. Reason for the Job
__________________
 Self Explanatory

 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific silicon paper grade 320 No specific soft hair brush
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 08-001 USA DOD-A-82720
 GENERAL PURPOSE ADHESIVE HONEYCOMB FILLER
 (Ref. 20-31-00) Material No. 11-002 USA MIL-PRF-680
 DRY CLEANING SOLVENT (VARSOL/WHITE SPIRIT)
 (Ref. 20-31-00) Material No. 16-016 C Z-12.383
 EXTERNAL DECORATION PAINT (Ref. 20-31-00) Material No. 19-003 USA AMS 3819
 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
 3. Job Set-up
__________

 Subtask 11-00-00-120-051
 A. Preparation of the Contact Surfaces
 (1) Rub the contact surface with silicon paper grade 320 to remove the signs of paint.
 EFF : ALL

11-00-00Page 228
May 01/05
R
 CES  Subtask 11-00-00-110-060

 B. Cleaning the Contact Surfaces
 (1) Clean the contact surface with a MISCELLANEOUS (Material No. 19-003) soaked in CLEANING AGENTS (Material No. 11-002). Carefully remove the grease from the surface.
 4. Procedure
_________ Subtask 11-00-00-915-061
 A. Installation of the Placard
 (1) Apply BONDING AND ADHESIVE COMPOUNDS (Material No. 08-001) on the contact surface. Lightly bend the placard to bond it better.
 Subtask 11-00-00-916-052
 B. Preparation of the Placard
 (1) Apply 2 layers of STRUCTURE PAINTS (Material No. 16-016) on the placard with a soft hair brush.
 5. Close-up
________ Subtask 11-00-00-942-061
 A. Make sure that the work area is clean and clear of tool(s) and other items.
 EFF : ALL

11-00-00Page 229
May 01/05
R
 CES

 TASK 11-00-00-370-002

 Application of Identification and Marking Paints
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific abrasive nylon pads No specific abrasive rotative brush No specific anti-dust pads No specific clean lint-free cloth No specific grade 220 emery cloth
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 07-018  USA BMS 10-72 TYPE V VARNISH (Ref. 20-31-00)
 Material No. 11-004  USA MIL-T-81533 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM) (Ref. 20-31-00)
 Material No. 19-003  USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
 3. Job Set-up
__________
 Subtask 11-00-00-110-062
 A. Cleaning of the External Surfaces
 (1) Clean the surface with a MISCELLANEOUS (Material No. 19-003) soaked in CLEANING AGENTS (Material No. 11-004) to remove all the signs of dirt.
 NOTE : Do the cleaning operation until the cloth you use is clean.
____
 EFF : ALL

11-00-00Page 230
May 01/05
R
 CES

 Subtask 11-00-00-440-050

 B. Surface Reactivation
 (1) Before you apply the paint, make all the surfaces rough with abrasive nylon pads and CLEANING AGENTS (Material No. 11-004).
 NOTE : Stop the reactivation procedure when the surface is
____ sufficiently rough. Be careful not to remove or damage the protection of the skin or composite fibers.
 NOTE : The surface on which you do the reactivation must be wet, but
____ it is possible to rub a dry surface if a vacuum cleaning device is available to remove the dust when you have rubbed the surface.
 (2)
 If necessary, remove the remaining sealant with grade 220 emery cloth.

 (3)
 Lightly rub the screw or rivet rows to remove all the black signs.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM PLACARDS AND MARKINGS(20)