11-00-00Page 210
Aug 01/05
R
CES
TASK 11-00-00-400-004
Installation of the Labels on Heat Resistant Ducting
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 08-004 USA MIL-A-25457 ADHESIVE SEALANT (Ref. 20-31-00)
Material No. 11-004 USA MIL-T-81533 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM) (Ref. 20-31-00)
3. Job Set-up
__________ Subtask 11-00-00-110-052
A. Cleaning
(1) Degrease and clean the surface to which the label is to be affixed using CLEANING AGENTS (Material No. 11-004), then thoroughly dry out.
4. Procedure
_________ Subtask 11-00-00-915-053
A. Label Installation
(1) Label to be bonded to fabric impregnated with silicone synthetic rubber.
(a) Bond the label with BONDING AND ADHESIVE COMPOUNDS (Material No. 08-004) as per Vendor instructions.
EFF : ALL
11-00-00Page 211
Aug 01/05
R
CES
(2) Label to be affixed to fabric impregnated with Viton synthetic rubber.
(a)
Apply BONDING AND ADHESIVE COMPOUNDS (Material No. 08-004) only after the Viton coating has been treated with a bond coat comprising MB primer of the same composition.
(b)
Let the primer dry for 30 minutes before you install the label.
5. Close-up
________ Subtask 11-00-00-942-053
A. Make sure that the work area is clean and clear of tool(s) and other items.
EFF : ALL
11-00-00Page 212
Aug 01/05
R
CES
TASK 11-00-00-400-005
Installation of the Labels on Laminated Tubing
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-004 USA MIL-T-81533 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM) (Ref. 20-31-00)
3. Job Set-up
__________ Subtask 11-00-00-110-053
A. Cleaning
(1) Degrease and clean the surface to which the label is to be affixed using CLEANING AGENTS (Material No. 11-004), then thoroughly dry out.
4. Procedure
_________ Subtask 11-00-00-915-054
A. Label Installation
(1)
Remove the backing paper.
(2)
Affix the label and smooth out working from the center outwards to prevent the formation of air bubbles.
(3)
Smooth out the whole surface.
5. Close-up
________ Subtask 11-00-00-942-054
A. Make sure that the work area is clean and clear of tool(s) and other items.
EFF : ALL
11-00-00Page 213
Aug 01/05
R
CES
TASK 11-00-00-400-006
Installation of the ESSO Labels
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific clean brush
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-003 USA ASTM D 740
METHYL-ETHYL-KETONE (Ref. 20-31-00) Material No. 11-004 USA MIL-T-81533
1.1.1TRICHLOROETHANE (METHYL CHLOROFORM)
(Ref. 20-31-00) Material No. 11-016 USA BOEING BAC 5000 BAC 5504 BAC 5750
CLEANING SOLVENT (Ref. 20-31-00)
3. Job Set-up
__________
Subtask 11-00-00-110-054
A. Cleaning
(1) Degrease and clean the surfaces on which you will bond the ESSO labels, with CLEANING AGENTS (Material No. 11-003) or CLEANING AGENTS (Material No. 11-004) or CLEANING AGENTS (Material No. 11-016) then thoroughly dry.
EFF : ALL
11-00-00Page 214
May 01/05
R
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM PLACARDS AND MARKINGS(16)
