__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific  emery cloth Grade 350
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 08-010  D DA-4-653-3E4 TWO COMPONENT EPOXY ADHESIVE (Ref. 20-31-00) Material No. 11-003 USA ASTM D 740 METHYL-ETHYL-KETONE (Ref. 20-31-00) Material No. 11-016 USA BOEING BAC 5000 BAC 5504 BAC 5750 CLEANING SOLVENT (Ref. 20-31-00)
 3. Job Set-up
__________ Subtask 11-00-00-110-057
 A. Cleaning
 (1) Roughen the surface on which you will have bond the label, using emery cloth Grade 350 and clean with CLEANING AGENTS (Material No. 11-003) or CLEANING AGENTS (Material No. 11-016), then thoroughly dry.
 EFF : ALL

11-00-00Page 220
May 01/05
R
 CES

 4. Procedure
_________

 Subtask 11-00-00-915-058
 A. Label Installation
 (1)
 Apply a coat of BONDING AND ADHESIVE COMPOUNDS (Material No. 08-010) to the surface on which you will bond the label.

 (2)
 Affix the label and apply light pressure to the label for about 30 seconds.

 NOTE : When you bond the label on a cylindrical component,
____ temporarily install a tie strap and leave in position until the adhesive compound is fully dry.
 5. Close-up
________ Subtask 11-00-00-942-058
 A. Make sure that the work area is clean and clear of tool(s) and other items.
 EFF : ALL

11-00-00Page 221
May 01/05
R
 CES

 TASK 11-00-00-400-010

R Installation of BSB (DUROFIX) Labels
 1. Reason for the Job
__________________
 This procedure gives the information necessary for installation of the decals (BSB) related to service and safety markings on the external surface of the aircraft.
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific lukewarm water
 No specific needle
 No specific plastic container
 No specific plastic scraper
 No specific rubber roller
 No specific soft hair brush
 No specific sponge

 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 05-029 F IPDA 28-05 FIXATIVE FOR PLACARD INSTALLATION (Ref. 20-31-00) Material No. 07-017 INTERNAL POLYURETHAN E VARNISH (Ref. 20-31-00) Material No. 07-018 USA BMS 10-72 TYPE V VARNISH (Ref. 20-31-00) Material No. 11-003 USA ASTM D 740 METHYL-ETHYL-KETONE (Ref. 20-31-00) Material No. 11-016 USA BOEING BAC 5000 BAC 5504 BAC 5750 CLEANING SOLVENT (Ref. 20-31-00) Material No. 19-003 USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
 EFF : ALL

11-00-00Page 222
Aug 01/05
 CES

 3. Job Set-up
__________

 Subtask 11-00-00-110-058
 A. Cleaning of the Contact Surfaces
 (1) Clean the decal contact surface with a MISCELLANEOUS (Material No. 19-003) soaked in CLEANING AGENTS (Material No. 11-003) or CLEANING AGENTS (Material No. 11-016).
 Subtask 11-00-00-915-062
 B. Preparation of the Bonding Material for the Decal NOTE : Obey the manufacturer's instructions and the safety precautions to
____
 use the bonding material.

 (1)
 If the paint is new, do the step that follows to prepare the bonding material.

 (a) Mix one volume of lukewarm water at a temperature between 30 and 40 deg.C (86 and 104 deg.F) with one volume of SPECIAL MATERIALS (Material No. 05-029) in a plastic container.

 (2)
 If the paint is not new, do the steps that follow to prepare the bonding material.

 (a)
 Apply the fixative C-Special of the SPECIAL MATERIALS (Material No. 05-029) on the paint of the applicable area.

 (b)
 Mix two volumes of lukewarm water at a temperature between 30 and 40 deg.C (86 and 104 deg.F) with one volume of the fixative UW of the SPECIAL MATERIALS (Material No. 05-029) in a plastic container.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM PLACARDS AND MARKINGS(18)