(3)
 Preparation for installation

 (a) Clean the contact surfaces with MISCELLANEOUS (Material No. 19-003) soaked with CLEANING AGENTS (Material No. 11-003).
 EFF : ALL

11-00-00Page 234
Aug 01/05
 CES

 (b)
 Use adhesive tape to show the limits of the bonded area.

 (c)
 Rub the contact surfaces with emery paper grade 320 to make the surface mat.

 (d)
 Remove the adhesive tape.

 (e)
 Clean the contact surfaces with MISCELLANEOUS (Material No. 19-003) soaked with CLEANING AGENTS (Material No. 11-003).

 Subtask 11-00-00-860-051
 B. Aircraft Maintenance Configuration
 (1) Before you install the reference triangle make sure that the rudder and/or the elevator are in the correct position
 -
for the rudder (Ref. TASK 27-24-00-820-001).

 -
for the elevator (Ref. TASK 27-34-00-820-003), or (Ref. TASK 27-34-00-820-003)

 4. Procedure
_________
 Subtask 11-00-00-915-065

 A. Installation of the Reference Triangle
 (1) Remove the protection paper from the reference triangle.
R (2) Install the reference triangle (Ref. AMM 11-21-27 P.Block 001) with R BONDING AND ADHESIVE COMPOUNDS (Material No. 08-001).
 (3) Use adhesive tape to hold the reference triangle during curing time.
 5. Close-up
________
 Subtask 11-00-00-942-063

 A. Put the aircraft back to its initial configuration.
 (1) Make sure that the work area is clean and clear of tool(s) and other items.
 EFF : ALL

11-00-00Page 235
Aug 01/05
 CES  TASK 11-00-00-370-003

 Apply Marking Paints with Stencils
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific access platform No specific brush No specific masking film No specific tape
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 07-018 USA BMS 10-72 TYPE V VARNISH (Ref. 20-31-00) Material No. 11-003 USA ASTM D 740 METHYL-ETHYL-KETONE (Ref. 20-31-00) Material No. 11-010 USA TT-I-735 GRADE A ISOPROPYL ALCOHOL (Ref. 20-31-00)
 C. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
SRM 512311,P.Block001
 EFF : ALL

11-00-00Page 236
May 01/05
R
 CES  3. Job Set-up

__________ Subtask 11-00-00-010-050
 A. Get Access
 (1) Put an access platform in position in the work area. Subtask 11-00-00-110-066
 B. Cleaning of the external surfaces
 WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL

_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
 (1) Clean the surface with CLEANING AGENTS (Material No. 11-010) or CLEANING AGENTS (Material No. 11-003) if the paint is fully cured, and let it dry.
 4. Procedure
_________ Subtask 11-00-00-370-052
 A. Apply Marking Paints with Stencils NOTE : The base paint must be sufficiently dry (the paint manufacturer
____ gives the indications "dry to tape" or "maskable drying time") before you apply the paint with a stencil.
 (1)
 Put the masking film or tape in position.

 (2)
 Refer to the supplier's instructions to mix the paint.

 (3)
 Apply the paint as a spray or with a brush.

 (a) For more information about the coatings (Ref. SRM 512311,P.Block001).
 NOTE : Make sure that you keep the contrast between the color of
____ the base paint and the marking.
 EFF : ALL

11-00-00Page 237
May 01/05
R
 CES

 (4) Remove all the masking material and touch up as necessary. Subtask 11-00-00-916-055
 B. Protection of External Markings
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM PLACARDS AND MARKINGS(22)