曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

The following procedures are applicable to the noted ACARS functions from the company pages.
Pre-Departure Clearance
The flight crew shall manually verify (compare) the filed flight plan versus the digital pre-departure clearance and shall initiate voice contact with Air Traffic Control if any question/confusion exists between the filed flight plan and the digital pre-departure clearance.
Digital-Automatic Information Service
The flight crew shall verify that the D-ATIS altimeter setting numeric value and alpha value are identical. If the D-ATIS altimeter setting numeric value and alpha values are different, the flight crew must not accept the D-ATIS altimeter setting.
Oceanic Clearances
The flight crew shall manually verify (compare) the filed flight plan versus the digital oceanic clearance and initiate voice contact with Air Traffic Control if any questions/confusion exists between the filed flight plan and the digital oceanic clearance.
Weight and Balance
The flight crew shall verify the Weight and Balance numeric and alphabetical values are identical. If the Weight and Balance numeric and alphabetical values are different, the flight crew must not accept the Weight and Balance data.
Takeoff Data
The flight crew shall verify the Takeoff Data numeric and alphabetic values are identical. If the Takeoff Data numeric and alphabetic values are different, the flight crew must not accept the Takeoff Data message.
Copyright . The Boeing Company. See title page for details.
Supplementary Procedures -Communications 737 Flight Crew Operations Manual

Cockpit Voice Recorder Test
YA613, YA626, YC153 - YC413, YK101 - YK104
Note: The Cockpit VOICE RECORDER switch must be in the ON position or at least one engine must be operating to perform this test.
Test switch ........................................................................................ Push After a slight delay: Test light........................................................................................ ON A tone may be heard through a headset plugged into the headset jack. Test switch ....................................................................................Release
Copyright . The Boeing Company. See title page for details.

737 Flight Crew Operations Manual

Electrical Power Up
The following procedure is accomplished to permit safe application of electrical power.
BATTERY switch ............................................................... Guard closed

STANDBY POWER switch ............................................... Guard closed

Verify that the STANDBY PWR OFF light is extinguished.
ALTERNATE FLAPS master switch ................................. Guard closed

Windshield WIPER selector(s) ...................................................... PARK

ELECTRIC HYDRAULIC PUMPS switches .................................. OFF

LANDING GEAR lever .....................................................................DN

Verify that the green landing gear indicator lights are illuminated.
Verify that the red landing gear indicator lights are extinguished.
WEATHER RADAR .......................................................................... Off

If external power is needed:
Verify that the GRD POWER AVAILABLE light is illuminated.
GRD POWER switch – ON
Verify that the SOURCE OFF lights are extinguished.
Verify that the TRANSFER BUS OFF lights are extinguished.
If APU power is needed:
Verify that the engine No. 1, APU and the engine No. 2 fire switches
are in.
Alert ground personnel before the following test is accomplished.
OVERHEAT DETECTOR switches – NORMAL
TEST switch – Hold to FAULT/INOP
Verify that the MASTER CAUTION lights are illuminated.
Copyright . The Boeing Company. See title page for details.
Supplementary Procedures -Electrical 737 Flight Crew Operations Manual

Verify that the OVHT/DET annunciator is illuminated. Verify that the FAULT light is illuminated. If the FAULT light fails to illuminate, the fault monitoring system is inoperative. Verify that the APU DET INOP light is illuminated. Do not operate the APU if the APU DET INOP light fails to illuminate.
TEST switch – Hold to OVHT/FIRE Verify that the fire warning bell sounds. Verify that the master FIRE WARN lights are illuminated. Verify that the MASTER CAUTION lights are illuminated. Verify that the OVHT/DET annunciator is illuminated. Master FIRE WARN light – Push
Verify that the master FIRE WARN lights are extinguished. Verify that the fire warning bell cancels.
Verify that the engine No. 1, APU and the engine No. 2 fire switches stay illuminated. Verify that the ENG 1 OVERHEAT and ENG 2 OVERHEAT
lights stay illuminated. EXTINGUISHER TEST switch – Check TEST Switch - Position to 1 and hold Verify that the three green extinguisher test lights are illuminated. TEST Switch - Release Verify that the three green extinguisher test lights are extinguished. Repeat for test position 2. APU - Start and on bus
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737NG機組操作手冊Flight Crew Operations Manual FCOM 1(76)