Electrical Harness Conduits - Corrosion Protection Figure 618/TASK 24-92-00-991-024
R 1EFF : 1 1 1CES ALL 1 111 24-92-00 Page 663 Feb 01/04
Location of Conduit Fittings Figure 619/TASK 24-92-00-991-025
R 1EFF : 1 1 1CES ALL 1 111 24-92-00 Page 664 Feb 01/04
5. Close-up
________ Subtask 24-92-00-410-062
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the access panels: 321AL, 322BL, 324AT.
(3)
Disconnect the aircraft from ground (Ref. TASK 12-34-24-869-002).
(4)
Remove the access platform(s).
R 1EFF : ALL 1 24-92-00Page 665 1 1 Feb 01/04 1 1 1CES 1 TASK 24-92-00-210-013
Inspection of the End Fittings of Electrical Conduits in Flap Track No. 2 Fairing
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND THE CAUTIONS INCLUDED IN
_______ THE REFERENCED PROCEDURES.
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL MATERIALS
_______ ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
1. Reason for the Job
__________________
Refer to the MPD TASK: 240000-08 Apply temporary protection to end fittings of electrical conduits in flap track No. 2 fairing.
R 1EFF : ALL 1 24-92-00Page 666 1 1 Feb 01/04 1 1 1CES 1
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific airless spray
No specific brush
No specific dental
No specific lint-free cloth
No specific seal tools
No specific adjustable access platform 3 m (9 ft. 10 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-004 USA MIL-T-81533
1.1.1TRICHLOROETHANE (METHYL CHLOROFORM)
(Ref. 20-31-00)
Material No. 15-008 AIB TN 10138 TYPE II GRADE 2 CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
12-34-24-869-002 Aircraft Grounding for the Maintenance Operations 24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied
from the External Power
24-92-00-991-006 Fig. 602
24-92-00-991-026 Fig. 620
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
24-92-00-991-027 Fig. 621
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R **ON A/C 301-399,
R 24-92-00-991-027-A Fig. 621A
R **ON A/C ALL
3. Job Set-up__________
Subtask 24-92-00-862-063
A. De-energize the aircraft electrical circuits (Ref. TASK 24-41-00-862-002).
Subtask 24-92-00-869-077
B. Connect the aircraft to the ground (Ref. TASK 12-34-24-869-002).
Subtask 24-92-00-010-063
C. Get Access
(1) Put the adjustable access platform in position at the flap track No. 2 fairing.
(2) For the left wing:
(a) Remove and retain the top cover of the movable fairing of the No. 2 flap track: 531AT.
(3) For the right wing:
(a) Remove and retain the top cover of the movable fairing of the No. 2 flap track: 631AT.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ELECTRICAL POWER 電源2(160)
