(4)
Make sure that the access door 121AL is open.
(5)
Make sure that the external power connector is not connected to the aircraft receptacle.
(6)
Make sure that a warning notice is in position on the access door 121AL to tell persons not to use the external power receptacle.
(7)
In the cockpit, on the overhead ELEC panel 35VU, make sure that these pushbutton switches are released:
-BAT 1, BAT 2,
-APU GEN,
-GEN 1, GEN 2,
-EXT PWR.
(8)
In the cockpit, make sure that a warning notice is in position to tell persons not to operate the pushbutton switches on these overhead panels:
-21VU (EMER ELEC PWR),
-35VU (ELEC).
(9)
In the cockpit, on the APU section of the overhead panel 25VU, make sure that a warning notice is in position to tell persons not to start the APU.
Subtask 24-42-55-865-051
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
122VU ELEC/EXT PWR/LT CLT/NOT IN/USE 6XG X30
4. Procedure
_________
**ON A/C 001-049, 051-062, 101-105, 151-152, 201-205,
(Ref. Fig. 401/TASK 24-42-55-991-001) R **ON A/C 063-099, 106-149, 153-199, 206-299, 301-399, 401-499,
(Ref. Fig. 401A/TASK 24-42-55-991-001-A)
**ON A/C 001-049, 051-062, 101-105, 151-152, 201-205,
Subtask 24-42-55-420-050
A. Installation of the contactor CAUTION : MAKE SURE THAT THE CONTACTOR LOCATING PIN IS CORRECTLY ENGAGED
_______ IN ITS RECESS LOCATED IN ONE POWER TERMINAL. THIS PREVENTS DAMAGE TO THE LOCATING PIN WHEN YOU APPLY THE TORQUE.
(1)
Install the contactor (3) on the 6 tapped barrels (5) of the contactor base (6).
(2)
TORQUE the captive screws (2) to between 23.90 and 26.55 lbf.in (0.27 and 0.30 m.daN).
(3)
Remove the blanking caps from the electrical connectors.
(4)
Make sure that the electrical connectors are clean and in the correct
condition.
(5) Connect the electrical connector (1). R **ON A/C 063-099, 106-149, 153-199, 206-299, 301-399, 401-499,
Subtask 24-42-55-420-050-A
A. Installation of the Contactor CAUTION : MAKE SURE THAT THE CONTACTOR LOCATING PIN IS CORRECTLY ENGAGED
_______ IN ITS RECESS LOCATED IN ONE POWER TERMINAL. THIS PREVENTS DAMAGE TO THE LOCATING PIN WHEN YOU APPLY THE TORQUE.
(1)
Install the contactor (3) on the module 20XX (4).
(2)
TORQUE the captive screws (2) to between 23.90 and 26.55 lbf.in (0.27 and 0.30 m.daN).
(3)
Remove the blanking caps from the electrical connector (1) and the electrical receptacle.
(4)
Make sure that the electrical connectors are clean and in the correct condition.
(5) Connect the electrical connector (1) to the contactor (3).
**ON A/C ALL
Subtask 24-42-55-865-052
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6XG.
Subtask 24-42-55-710-050
C. Test of the Annunciator Lights in the cockpit
(1)
Energize the ground service network
(Ref. TASK 24-42-00-861-001).
(2)
FOR 12XX On the FWD ATTENDANT panel 120RH, push the MAIN ON pushbutton switch. Make sure that the CEILING AFT RH, WINDOW FWD LH and WINDOW AFT LH annunciator lights come on.
(3)
FOR 14XX On the FWD ATTENDANT panel 120RH, push the MAIN ON pushbutton switch. Make sure that the CEILING AFT LH, WINDOW FWD RH and WINDOW AFT RH annunciator lights come on.
5. Close-up
________ Subtask 24-42-55-862-050
A. Put the aircraft back to its initial configuration.
(1) De-energize the ground service network
(Ref. TASK 24-42-00-862-001).
Subtask 24-42-55-410-050
B. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the front panel (8) of the panel 123VU.
(3)
Install the Third Occupant seat (Ref. TASK 25-11-41-400-001).
(4)
Remove the warning notice(s).
(5)
Close the access door 121AL.
(6)
Remove the access platform(s).
1EFF : ALL 1 24-42-55Page 410 1 1 May 01/04R 1 1 1CES 1
中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM ELECTRICAL POWER 電源2(96)
