-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
1.
Reason for the Job
__________________
Refer to the MPD TASK: 200003-03
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific adjustable access platform 9 m (29 ft. 6 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
ESPM 205332 ESPM 205500 24-92-00-991-035 Fig. 630
1EFF : ALL 1 24-92-00Page A600 1 1 May 01/04R 1 1 1CES 1
3. Job Set-up
__________ Subtask 24-92-00-860-075
A. Aircraft Maintenance Configuration
(1)
Put a warning notice in the cockpit to tell persons not to operate the pitch controls.
(2)
Put a warning notice in position to tell persons not to pressurize the Green and Yellow hydraulic systems.
Subtask 24-92-00-010-070
B. Get Access
(1)
Put an adjustable access platform in position at the vertical stabilizer leading-edge.
(2)
Remove the access panel 324AT.
4. Procedure
_________ Subtask 24-92-00-210-070
A. Inspection
(Ref. Fig. 630/TASK 24-92-00-991-035)
(1) Do a general visual inspection of the components on these harnesses:
-4202VB,
-4204VB.
(a)
Do a check of the general condition of these components and make sure that they are correctly attached:
-electrical bonding leads,
-braided conduits,
-clamps,
-electrical connectors,
-braided shields.
(b)
Make sure that there is no sign of contamination (Ref. ESPM 205500) and corrosion (Ref. ESPM 205332).
1EFF : ALL 1 24-92-00Page A601 1 1 May 01/04R 1 1 1CES 1
Electrical Harnesses - Inspection Figure 630/TASK 24-92-00-991-035
1EFF : 1 1R 1CES ALL 1 11 1 24-92-00 Page A602 May 01/04
5. Close-up
________ Subtask 24-92-00-410-071
A. Close Access
(1) Install the access panel 324AT. Subtask 24-92-00-860-076
B. Aircraft Maintenance Configuration
(1)
Remove the access platform(s).
(2)
Remove the warning notice(s).
1EFF : ALL 1 24-92-00Page A603 1 1 May 01/04R 1 1 1CES 1
TASK 24-92-00-210-023
Check that Connector is Correctly Tightened by Measurement of the Resistance with a Loop Tester
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND THE CAUTIONS INCLUDED IN
_______
THE REFERENCED PROCEDURES.
1. Reason for the Job
__________________
Refer to the MPD TASK: 200001-02 Do this procedure to make sure that these connectors are correctly tightened; to do this check, measure the resistance with a loop tester:
R - 4005VC, 4007VC, 4009VC, 4011VC, 4013VC, 4015VC, 4017VC, 4019VC, LH side R - 4006VC, 4008VC, 4010VC, 4012VC, 4016VC, 4018VC, 4020VC, RH side
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific multimeter
No specific test set-loop resistance
No specific access platform 3.5 m (11 ft. 6 in.)
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ELECTRICAL POWER 電源2(166)
