(11)
 Put warning notices in position on the rudder pedals (CAPT and F/0) to tell persons not to operate them.

 (12)
 Install the PIN - RIGGING (98D27207547000) or RIGGING PIN SET (98D27207516000) (6) on the cable quadrant (5).

 (13)
 Depressurize the Blue hydraulic system (Ref. TASK 29-10-00-864-003).

 (14)
 De-energize the aircraft electrical cicuits (Ref. TASK 24-41-00-862-002).

 (15)
 Remove the control rod (7) between the mixer and the cable quadrant

 (5) (Ref. TASK 27-21-00-840-001).

 (16)
 Do a check of the dimension 22.9 +2 -2 mm (0.9015 +0.0787 -0.0787 in.) on the cable quadrant (5). If the dimension is not correct, adjust it as follows:

 (a)
 Remove the lockwire from the nuts (3) and discard it.

 (b)
 Loosen the nuts (3).

 (c)
 Turn the bolts (4) until you get the correct dimension.

 (d)
 Tighten the nuts (3). Do not safety the nuts (3) at this time.

R 1EFF : 106-149, 218-299, 301-399, 401-499, 1 27-21-00Page 545 1 1 Aug 01/05 1 1 1CES 1 **ON A/C ALL

 4. Procedure
_________
 **ON A/C 001-049, 051-099, 101-105, 151-199, 201-217,

 (Ref. Fig. 507/TASK 27-21-00-991-008) R **ON A/C 106-149, 218-299, 301-399, 401-499,
 (Ref. Fig. 507A/TASK 27-21-00-991-008-A)
 **ON A/C ALL

 (Ref. Fig. 508/TASK 27-21-00-991-009)
 **ON A/C 001-049, 051-099, 101-105, 151-199, 201-217,

 Subtask 27-21-00-820-053
 A. Adjustment of the Cable Linkage Assy
 (1)
 Measure the ambient temperature with a thermometer.

 (2)
 Use the adjustment graph to find the position of the index of the cable tension regulator (1), in relation to the ambient temperature.

 (3)
 Install the BRACKET TENSION REGULATOR-RUDDER CONTROL (98D27203500000)

 (10) on the mark of the flange of the cable tension regulator (1) (access door 811).
 NOTE : This tool is used to align the mark on the cable tension
____ regulator with the related graduation on the fixed scale.
 (4)
 Bend the two cables to the same value and release them quickly. When you release the cables, make sure that the two quadrants of the tension regulator move easily (it must not be caught).

 (5)
 Remove the locking clips (8) from the turnbuckles (9).

 (6)
 Turn the 2 turnbuckles (9) by the same value to adjust the length of the cable loop so that:

 (a)
 Read the value on the fixed scale with a mirror and check that the position of the index of the tension regulator (1) agrees with the values found on the graph.

 (b)
 You can install the locking clips (8) on the turnbuckles (9).

 (c)
 You can easily install and remove the PIN, RIGGING - RUDDER CONTROL (98A27901002000) (2) on the input lever of the cable tension regulator (1).

 (7)
 If you cannot install the PIN, RIGGING - RUDDER CONTROL (98A27901002000) easily, adjust the bolt (4):

 (a)
 If necessary, remove the lockwire from the nuts (3) and discard it.

 (b)
 Loosen the nuts (3) from the cable quadrant (5).

 (c)
 Turn the bolts (4) on the cable quadrant (5) so that:

 -The position of the index of the tension regulator (1) agrees with the values found on the graph.
 -You can easily install and remove the PIN, RIGGING - RUDDER CONTROL (98A27901002000) (2) on the input lever of the cable tension regulator (1).
 (d)
 Do a check of the dimensions 25 +2 -2 mm (0.9842 +0.0787 -0.0787 in.).

 (e)
 Tighten the nuts (3) on the cable quadrant (5). Do not safety the nuts (3) at this time.

 (8)
 If you cannot adjust the control cables, do a visual inspection of the pulleys and the tension regulator.

 (a) If they are in good condition:
 1_ Make a mark on each front cable.
 2_ Pull the cables to the rear until the position of the index
 agrees with the value found on the graph.
 3_ Keep the cables pulled and make a new mark on each front cable
 then release the cables. 

R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 27-21-00Page 547 1201-217, 1May 01/05 1 1 1CES 1

 Component Location Figure 507/TASK 27-21-00-991-008- 12 (SHEET 1)
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 27-21-00Page 548 1201-217, 1May 01/05 1 1 1CES 1

 Component Location Figure 507/TASK 27-21-00-991-008- 22 (SHEET 2)
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 27-21-00Page 549 1201-217, 1May 01/05 1 1 1CES 1
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱1(150)