R Location of the Tools Figure 601/TASK 27-14-00-991-004
1EFF : 1 1 1CES ALL 1 111 27-14-00 Page 604 May 01/04
4. Procedure_________
Subtask 27-14-00-210-052
A. Check for General Condition
(1) Do a visual check of the servo control bearings.
(2) Do a visual check of the aileron hinge bearings.
(3) Make sure that the that the liners are not damaged.
R R R NOTE : The liner is a coat of teflon between the bearing case and the____ ball. It lets the ball turn with a minimum of friction (self lubricating).
R R If you can see the liner, replace the related servo control (Ref. TASK 27-14-51-000-001) and (Ref. TASK 27-14-51-400-001).
Subtask 27-14-00-220-050
B. Check of the Aileron Servo Controls and Hinge Bearings for too much Play and Condition
(1) On the panel 24VU, release the FLT CTL/ELAC 2 pushbutton switch (the OFF legend comes on).
NOTE : The check is only given for one surface. Do the same____ operations for the other surface.
(2) Connect the SPRING SCALE ASSY (97A27902016000) or GAGE ASSY - PUSH-PULL (97A27003000000) or GAGE ASSY - PUSH-PULL (97A27003000001) to the LOAD APPLICATION TOOL - ELEVATOR, AILERON, RUDDER (98D27303000001) and apply 30 daN (67.4426 lbf) in the up direction on the trailing edge.
NOTE : If you see oscillations when the servo control is in active____ mode, do a check of these oscillations (Ref. TASK 27-14-00-200-001)
(3) Continue to apply this force and set the dial indicator to zero.
(4) Release the force.
(5) At the same position, apply 30 daN (67.4426 lbf) in the down direction on the trailing edge.
(6) Continue to apply this force and read the value on the dial indicator.
(7) Release the force on the trailing edge.
(8)
Change the servoing of the ailerons as follows:
(a)
On the panel 24VU, push the FLT CLT/ELAC 2 pushbutton switch (the OFF legend goes off).
(b)
On the panel 23VU, release the FLT CTL/ELAC 1 pushbutton switch (the OFF legend comes on).
(9)
At the same position, apply 30 daN (67.4426 lbf) in the up direction on the trailing edge.
(10)
Continue to apply this force and set the dial indicator to zero.
(11)
Release the force.
(12)
At the same position, apply 30 daN (67.4426 lbf) in the down direction on the trailing edge.
(13)
Continue to apply this force and read the value on the dial
indicator.
(14)
Release the force on the trailing edge.
(15)
For each measurement, if the distance is more than 10 mm (0.3937 in.) between the two positions:
-repair the structure/aileron, structure/servo control or servo control/aileron bearings (Ref. TASK 27-14-41-200-001), (Ref. TASK 27-14-51-200-001).
NOTE : This 10 mm (0.3937 in.) value includes 4 mm (0.1574 in.) of
____ surface bending as the result of 30 daN (67.4426 lbf) applied force.
5. Close-up
________
Subtask 27-14-00-080-050
A. Removal of the Tools.
(Ref. Fig. 601/TASK 27-14-00-991-004)
(1)
Remove the CHECK TOOL - AILERON, ELEVATOR, RUDDER (98D27303003001) or CHECK TOOL (ORAP) - AILERON, ELEVATOR, RUDDER (98D27303022000) , the SPRING SCALE ASSY (97A27902016000) or GAGE ASSY - PUSH-PULL (97A27003000000) or GAGE ASSY - PUSH-PULL (97A27003000001) and the LOAD APPLICATION TOOL - ELEVATOR, AILERON, RUDDER (98D27303000001).
(2)
Remove the PIN-SIDE STICK LOCKING (98D27903500000) from the two side stick controllers.
(3)
Make sure that the work area is clean and clear of tool(s) and other items.
1EFF : ALL 1 27-14-00Page 606 1 1 Aug 01/05R 1 1 1CES 1
Subtask 27-14-00-410-055
B. Close Access
(1)
575KB, 575MB, 590AB, 590BB for the left aileron.
(2)
675KB, 675MB, 690AB, 690BB for the right aileron.
(3) Remove the access platform(s). Subtask 27-14-00-860-051
C. Put the aircraft back to its initial configuration.
(1)
Depressurize the Green hydraulic system (Ref. TASK 29-23-00-864-001).
(2)
Depressurize the Blue hydraulic system (Ref. TASK 29-10-00-864-003).
(3)
On the panel 23VU, push the FLT CTL/ELAC 1 pushbutton switch (the OFF legend goes off).
(4)
Remove the warning notice(s).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱1(83)
