(3)
Make sure that the parts retained from the removed component are clean and in the correct condition.
(4)
Lubricate these parts with SPECIAL MATERIALS (Material No. 05-002):
-for hinge No.s 2 and 3, the bushes (18)
-
the bushes (26), (41) and (50)
-
the hinge pins (19) and (42)
-
the flanged bushes (14)
-
the pins (15)
-
the installed bushes in the attachment brackets.
If the aileron is safetied with ABS 0738 nuts, do the steps that follow:
(5)
Use a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026) to clean:
-
the heads of the bolts (84), (95) and (97)
-
the nuts (75), (106) and (107)
-
the ends of the bonding straps (77), (90) and (99).
(6)
Clean the component interfaces and/or the adjacent areas with a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026).
(7)
Make sure that the parts retained from the removed component are clean and in the correct condition.
(8)
Lubricate these parts with SPECIAL MATERIALS (Material No. 05-002):
-for hinge No.s 2 and 3, the bushes (70)
-
the bushes (78), (91) and (100)
-
the hinge pins (71) and (92)
-
the flanged bushes (66)
-
the pins (67)
-
the installed bushes in the attachment brackets.
Subtask 27-14-41-420-051
B. Install the Bushes in the Hinges
If the aileron is safetied with STA-LOK nuts, do the steps that follow:
(1)
For the hinge No. 1, install the bush (26).
(2)
For the hinge No.s 2 and 3, install the bushes (18) and (26).
(3)
For the hinge No.s 4 and 5, install the bushes (41) and (50).
(4)
For the hinge No. 1, install the bush (78).
If the aileron is safetied with ABS 0738 nuts, do the steps that follow:
R 1EFF : 001-003, 051-052, 1 27-14-41Page 423 1 1 May 01/05 1 1 1CES 1
(5)
For the hinge No.s 2 and 3, install the bushes (70) and (78).
(6)
For the hinge No.s 4 and 5, install the bushes (91) and (100).
R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 27-14-41-420-053-A
A. Preparation for Installation
(Ref. Fig. 402A/TASK 27-14-41-991-002-B)
(1)
Use a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026) to clean:
-
the heads of the bolts (23), (34), (45) and (47)
-
the nuts (56) and (57)
-
the ends of the bonding straps (27), (40) and (49).
(2)
Clean the component interfaces and/or the adjacent areas with a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026).
(3)
Make sure that the parts retained from the removed component are clean and in the correct condition.
(4)
Lubricate these parts with SPECIAL MATERIALS (Material No. 05-002):
-for hinge No.s 2 and 3, the bushes (20)
-
the bushes (28), (41) and (50)
-
the hinge pins (21) and (42)
-
the flanged bushes (16)
-
the pins (17)
-
the installed bushes in the attachment brackets.
Subtask 27-14-41-420-051-A
B. Install the Bushes in the Hinges
(1)
For the hinge No. 1, install the bush (78).
(2)
For the hinge No.s 2 and 3, install the bushes (70) and (78).
(3)
For the hinge No.s 4 and 5, install the bushes (91) and (100).
**ON A/C ALL
Subtask 27-14-41-560-050
C. Preparation of a Replacement Component
(1)
If the aileron is to be replaced, install the LIFTING FRAME ASSEMBLY (AILERON) (98D27104001000):
(a)
Make sure that the side plates on the LIFTING FRAME ASSEMBLY (AILERON) are correctly installed.
(b)
Make sure that the adjuster assemblies on the LIFTING FRAME ASSEMBLY (AILERON) are as far apart as possible.
(2)
Lift the LIFTING FRAME ASSEMBLY (AILERON) with the crane and put the LIFTING FRAME ASSEMBLY (AILERON) around the aileron, at the same distance from each end.
NOTE : The weight of the aileron and the brackets is 50 kg (110.2311
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱1(92)
