R  3. Job Set-up__________ 
R  Subtask 28-43-21-941-060 
R  A. Safety Precautions 
R  WARNING : OBEY THE FUEL SAFETY PROCEDURES._______ 
R  (1) Make sure that the safety barriers are in position. 
R  (2) You must obey the fuel safety procedures (Ref. TASK 28-00-00-910-001) 
R  when you do work on the fuel system. 
R  Subtask 28-43-21-860-052 
R  B. Aircraft Maintenance Configuration 
R  (1) Make sure that the access platform is in position below the 
R  applicable Magnetic-Level-Indicator (MLI) rod. 
R  4. Procedure_________ 
R  (Ref. Fig. 403/TASK 28-43-21-991-003) 
R  Subtask 28-43-21-420-056 
R  A. Preparation for Installation 
R  WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL_______ 
R  MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. 
R  OBEY THE MANUFACTURERS INSTRUCTIONS. 
R  PUT ON PROTECTIVE CLOTHING. 
R  DO NOT GET THEM IN YOUR MOUTH. 
R  DO NOT SMOKE. 
R  DO NOT BREATHE THE GAS. 
R  THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. 
R  GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED. 
R  (1) Clean the component interfaces and the adjacent areas with a 
R  MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS 
R  (Material No. 11-004) 
R  (2) Do an inspection of the component interface and/or the adjacent area. 
R  (3) Make sure that the parts retained from the removed component are 
R  clean and in the correct condition.

R  Subtask 28-43-21-420-053 
R  B. Installation of the Magnetic-Level-Indicator Rod 
R  (1) Install the MLI rod (2) in the MLI housing. 
R  (2) Push the MLI rod (2) fully in, turn through 90 deg. and lock in 
R  position. 
R  Subtask 28-43-21-710-051 
R  C. Test 
R  CAUTION : DO NOT LET THE MLI's FALL FREELY._______ 
R  (1) Release the MLI rod (2) and make sure it extends fully and smoothly. 
R  (2) Push the MLI rod (2) fully in and lock in position. 
R  5. Close-up________ 
R  Subtask 28-43-21-942-052 
R  A. Removal of Equipment 
R  (1) Remove the safety barriers. 
R  (2) Make sure that the work area is clean and clear of tool(s) and other 
R  items. 
R  (3) Remove the access platform(s). 
R  (4) Remove the ground support and maintenance equipment, the special and 
R  standard tools and all other items.

 Removal of the Magnetic-Level-Indicator Assembly 56QM Thru 63QM, 200QM, 201QM, 208QM, 209QM
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
 START A TASK ON OR NEAR:

 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
 GEAR.

 1. Reason for the Job
__________________
R R Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers
 No specific adjustable access platform 4 m (13 ft. 1 in.)
 98D57004014000 1 HOOK-COVER (RIB2-SURGE DOORS)

 1EFF : 301-399, 1 28-43-21Page 425 1 1 Aug 01/04 1 1 1CES 1 B. Referenced Information

 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
28-10-00-910-001 Safety Procedures When You Do Work in a Fuel Tank 28-25-00-650-001 Pressure Defuel 28-25-00-650-003 To Drain Remaining Fuel from the Wing Tanks and the
 Center Tank
 57-27-11-000-001  Removal of the Access Panel (540AB, 540BB, 540CB, 540DB, 540EB, 540FB, 540GB, 640AB, 640BB, 640CB, 640DB, 640EB, 640FB, 640GB)
 57-27-11-000-002  Removal of the Access Panel (540HB, 540JB, 540KB, 540LB, 540MB, 540NB, 540PB, 540QB, 540RB, 550AB, 550BB, 550CB, 550DB, 560AB, 640HB, 640JB, 640KB, ....)
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUEL 燃油6(49)