(2)
Make sure that the parts retained from the removed component are clean and in the correct condition.
(3)
Do an inspection of the component interface and/or the adjacent area.
1EFF : ALL 1 28-46-17Page 410 1 1 Aug 01/05 1 1 1CES 1 Subtask 28-46-17-420-052
B. Installation of the Temperature Sensor 29QJ1 (29QJ2)
(1)
Install the sensor (7) with the bolts (3) and (5) and the washers (2) and (6).
(2)
TORQUE the bolt (3) to between 0.225 and 0.28 m.daN (19.91 and 24.77 lbf.in).
(3)
TORQUE the bolt (5) to between 0.45 and 0.56 m.daN (39.82 and 49.55 lbf.in).
(4)
Apply SEALANTS (Material No. 09-007) to the bolts (3) and (5).
(5)
Remove the blanking caps from the electrical connectors.
(6)
Connect the electrical connectors of the cable (1) and tighten the connector screws (4).
(7)
Install the cable (1) in the cable clamp and tighten the cable clamp screw (8).
Subtask 28-46-17-865-053
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit
breaker(s): R 3QA, 10QA, 31QA, 32QA, 1QL, 2QL, 3QL.
Subtask 28-46-17-740-050
D. BITE Test
(1) Do the tank-level-sensing functional (BITE) test (Ref. TASK 28-46-00-740-001).
1EFF : ALL 1 28-46-17Page 411 1 1 May 01/04 1 1 1CES 1
5. Close-up
________ Subtask 28-46-17-410-052
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the applicable access panel 540AB (640AB) (Ref. TASK 57-27-11-400-001):
-
FOR 29QJ1
install 540AB
-
FOR 29QJ2
install 640AB.
Subtask 28-46-17-650-054
B. Fuel Configuration
(1) Refuel, defuel or transfer fuel as necessary (Ref. TASK 12-11-28-650-003), (Ref. TASK 28-25-00-650-001) or (Ref. TASK 28-25-00-869-001).
Subtask 28-46-17-942-051
C. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Remove the warning notice(s).
(3)
Remove the access platform(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 28-46-17Page 412 1 1 May 01/04R 1 1 1CES 1
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
TASK 28-46-17-000-002 Removal of the Temperature Sensor 30QJ1 (30QJ2) WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking caps
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific access platform 3.8 m (12 ft. 6 in.)
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 28-46-17Page 413 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
28-10-00-910-001 Safety Procedures When You Do Work in a Fuel Tank 28-10-00-910-002 Access to the Fuel Tanks and the Work Areas 28-25-00-650-001 Pressure Defuel 28-25-00-650-003 To Drain Remaining Fuel from the Wing Tanks and the
Center Tank
57-27-11-000-002 Removal of the Access Panel (540HB, 540JB, 540KB, 540LB, 540MB, 540NB, 540PB, 540QB, 540RB, 550AB, 550BB, 550CB, 550DB, 560AB, 640HB, 640JB, 640KB, ....)
28-46-17-991-001 Fig. 401
3. Job Set-up
__________
Subtask 28-46-17-941-051
A. Safety Precautions
WARNING : OBEY THE SAFETY PROCEDURES WHEN YOU DO WORK IN A FUEL TANK.
_______
(1)
You must obey the fuel safety procedures (Ref. TASK 28-10-00-910-001) when you do work in a fuel tank.
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUEL 燃油6(93)
