_______
 (1)
 Put the safety barriers in position.

 (2)
 You must obey the fuel safety procedures (Ref. TASK 28-00-00-910-001) when you do work on the fuel system.

 4. Procedure
_________
 (Ref. Fig. 401/TASK 28-43-23-991-001) Subtask 28-43-23-020-054
 A. Removal of the Magnetic Level-Indicator Rod 92QM
 (1)
 Push the Magnetic Level Indicator (MLI) rod (5) in against the spring

 (2) and turn it through 90 deg. to release.

 (2)
 Pull the MLI rod (5) out until the magnet (1) touches the seal (3). Continue to pull until the MLI rod (5) is out of the MLI lower housing (4).

 1EFF : ALL 1 28-43-23Page 402 1 1 Feb 01/98 1 1 1CES 1

 Magnetic Level Indicator 92QM - Rod Detail
 Figure 401/TASK 28-43-23-991-001
 1EFF :  ALL  1  28-43-23 Page 403 
1  1  Feb 01/98
 1  1
 1CES  1

 TASK 28-43-23-400-001 Installation of the Magnetic Level-Indicator Rod 92QM. WARNING : MAKE SURE THAT THE FLIGHT CONTROL SAFETY-LOCKS AND THE WARNING
_______ NOTICES ARE IN POSITION.
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific  safety barriers
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-004  USA MIL-T-81533 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM) (Ref. 20-31-00)
 Material No. 19-003  USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
 C. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
28-00-00-910-001 Fuel Safety Procedures 28-43-23-991-001 Fig. 401
 1EFF : ALL 1 28-43-23Page 404 1 1 Feb 01/98 1 1 1CES 1

 3. Job Set-up
__________ Subtask 28-43-23-941-060
 A. Safety Precautions
 WARNING : OBEY THE FUEL SAFETY PROCEDURES.

_______
 (1)
 Make sure that the safety barriers are in position.

 (2)
 You must obey the fuel safety procedures (Ref. TASK 28-00-00-910-001) when you do work on the fuel system.

 4. Procedure
_________
 (Ref. Fig. 401/TASK 28-43-23-991-001) Subtask 28-43-23-420-061
 A. Preparation for Installation
 (1)
 Clean the component interfaces and the adjacent areas with a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-004).

 (2)
 Do an inspection of the component interface and/or the adjacent area.

 (3)
 Make sure that the parts retained from the removed component are clean and in the correct condition.

 Subtask 28-43-23-420-056
 B. Installation of the Magnetic Level-Indicator Rod 92QM
 (1)
 Carefully push the Magnetic Level Indicator (MLI) rod (5) into the MLI lower housing (4) until the magnet (1) is past the O-ring (3).

 (2)
 Push the MLI rod (5) fully in and turn through 90 deg and lock in position.

 Subtask 28-43-23-710-050
 C. Operational Test
 CAUTION : DO NOT LET THE MLI's FALL FREELY.

_______
 (Ref. Fig. 401/TASK 28-43-23-991-001)

 1EFF : ALL 1 28-43-23Page 405 1 1 Feb 01/98 1 1 1CES 1

 (1)
 Release the MLI rod (5) and make sure it extends fully and smoothly.

 (2)
 Retract the MLI rod (5) and lock in position.

 5. Close-up
________ Subtask 28-43-23-942-050
 A. Removal of Equipment
 (1)
 Remove the safety barriers.

 (2)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (3)
 Remove the warning notice(s).

 1EFF : ALL 1 28-43-23Page 406 1 1 Feb 01/98 1 1 1CES 1 TASK 28-43-23-000-002

 Removal of the Magnetic Level-Indicator Lower-Housing 91QM.
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUEL 燃油6(61)