Subtask 29-00-00-865-052
B. Make sure that this(these) circuit breaker(s) is(are) closed: -------------------------------------------------------------------------------
PANEL ------ DESIGNATION ------------------------------------------------------ IDENT. LOCATION-------------------
49VU FLIGHT CONTROLS/ELAC1/NORM/SPLY 15CE1 B11
49VU FLIGHT CONTROLS/SEC1/NORM/SPLY 21CE1 B08
105VU FLIGHT CONTROLS/ELAC2/STBY SPLY 16CE2 A02
105VU FLT CTL/ELAC1/STBY SPLY 16CE1 A01
105VU FLT CTL/SEC1/STBY SPLY 22CE B01
121VU AUTO FLT/FAC2/28VDC 5CC2 M19
121VU AUTO FLT/FAC2/26VAC 14CC2 M18
121VU HYDRAULIC/SOL VALVES/G/Y/B/LEAK/TST 1881GP N35
121VU HYDRAULIC/SOL VALVES/G/Y/PTU 1801GL N34
121VU FLIGHT CONTROLS/SEC3/SPLY 21CE3 Q19
121VU FLIGHT CONTROLS/SEC2/SPLY 21CE2 Q18
121VU FLIGHT CONTROLS/ELAC2/NORM/SPLY 15CE2 R20
Subtask 29-00-00-865-055
C. Open, safety and tag this(these) circuit breaker(s):
------PANEL ------------------------------------------------------DESIGNATION -------------------IDENT. LOCATION
-------------------------------------------------------------------------------121VU HYDRAULIC/HYD POWER/Y 3803GX N30 123VU Y HYD/ELEC/PUMP 3802GX AB06 123VU Y HYD/ELEC/ELEC PUMP/NORM 3801GX AB03
Subtask 29-00-00-860-056
D. Aircraft Maintenance Configuration
(1)
Connect a ground hydraulic supply with a flowmeter to the ground test connections of the Yellow hydraulic system.
(2)
In the main landing gear compartment, disconnect the PTU isolation coupling (Ref. TASK 29-23-00-860-001).
(3)
Energize the aircraft electrical circuits (Ref. TASK 24-41-00-861-002).
(4)
Set the ECAM system to on (Ref. TASK 31-60-00-860-001).
1EFF : ALL 1 29-00-00Page 652 1 1 Aug 01/05R 1 1 1CES 1
(5)
On the ECAM control panel on the center pedestal, push the F/CTL pushbutton (P/B). Make sure the lower display unit (DU) shows the F/CTL page.
(6)
Pressurize the Yellow hydraulic system from the ground supply (Ref. TASK 29-10-00-863-002).
(7)
On the overhead panel 23VU, make sure that the ELAC 1 and SEC 1 pushbutton switches P/BSW are set to on (OFF and FAULT lights not on).
(8)
On the overhead panel 24VU, make sure that the ELAC 2, SEC 2, SEC 3 and FAC 2 P/BSW are set to on (OFF and FAULT lights not on).
(9)
On the overhead panel 40VU set the PTU P/BSW to OFF (the OFF light comes on).
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
(10)
Operate the sidestick and rudder pedals to put the control surfaces associated with the Yellow hydraulic system in the 0 deg position (spoilers retracted).
(11)
Keep all of the control surfaces stopped in the 0 deg (retracted) position during measurement of internal leakage.
NOTE : Do the checks of internal leakage with the hydraulic fluid at
____ its usual working temperature of between 20 deg.C (68.00 deg.F) and 60 deg.C (140.00 deg.F).
4. Procedure
_________
Subtask 29-00-00-280-061
A. Check of the Internal Leakage of the Yellow Hydraulic System
(1) Measurement of the Yellow system (complete) internal leakage
(a)
On the overhead maintenance panel 50VU, make sure that the HYD/LEAK MEASUREMENT VALVES/Y P/BSW is set to on (OFF light not on).
(b)
On the overhead panel 40VU, make sure that the PTU P/BSW is set to OFF (the OFF light is on).
1EFF : ALL 1 29-00-00Page 653 1 1 Aug 01/05R 1 1 1CES 1
(c) Monitor the flow shown on the ground supply flowmeter. It must not be more than 10.0 l.min (2.6416 USgal.mn).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM HYDRAULIC POWER 液壓1(84)
