(d)
Move the blast tube (55) outboard. Align the bolt holes of the blast tube (55) with the bolt holes on the D nose section of Rib
11.
(e)
Put the cradle (49) in position and install the bolts (47) and
(59) and the washers (48).
(f)
Push the duct (37) against the cradle (49) and install the cradle (57), the bolt (56) and the nut (58).
(5)
To install intermediate rib:
-put the center rib (73) in position between the support ribs (62) and (75).
-install the bolts (65) and (76) and the nuts (66)and (74)
-
put the lower bracket (72) and the support bracket (78) in position and install the bolts (71) and the nuts (77)
-
put the top bracket (67) in position and install the bolts (68), the washers (69) and the nuts (64).
-
put the support bracket (63) in position on the rib supports (75) and the top bracket (67).
-install the bolts (61), (80) and (81) and the nuts (60), (70) and (79).
(a)
Put the end of the bonding strap (41) in position on the duct (37).
(b)
Install the screw (42), the washer (40) and the nut (39) (Ref. TASK 20-28-00-912-004).
(c)
Install the duct (3) as given before.
(6)
To install the duct (52) with the duct (37) removed: (Ref. Fig. 402/TASK 30-11-42-991-002, 403/TASK 30-11-42-991-003)
(a)
Put the duct (52) in position adjacent to the duct (94).
(b)
Install the clamp (53) and tighten the clamp nut to between 0.39 and 0.51 m.daN (34.51 and 45.13 lbf.in).
(c)
Put the end of the bonding strap (41) in position on the duct (52).
(d)
Install the screw (50), the washer (51) and the nut (54) (Ref. TASK 20-28-00-912-004).
(e)
Install the duct (37) as given before.
(7)
To install the duct (94): (Ref. Fig. 401/TASK 30-11-42-991-001, 402/TASK 30-11-42-991-002, 403/TASK 30-11-42-991-003)
R (a) Install the new seal (98) in the end of the duct (94).
(b)
Put the duct (94) in position in the duct box (104) and correctly align it with the duct (52).
(c)
Install the clamp (53) and TORQUE the clamp nut to between 0.39 and 0.51 m.daN (34.51 and 45.13 lbf.in).
(d)
Put the ends of the bonding straps (96) and (97) in position on the duct (94).
(e)
Install the screw (95), the washer (101) and the nut (100) (Ref. TASK 20-28-00-912-004).
(8)
To install the duct box (104) with the duct (94) removed: (Ref. Fig. 402/TASK 30-11-42-991-002, 403/TASK 30-11-42-991-003)
(a)
Put the duct box (104) in position and install the bolts (106) and (102) and the washers (103) and (105).
(b)
Safety the bolts (106) and (102) with MISCELLANEOUS (Material No. 19-010).
(9)
Install the telescopic duct (Ref. TASK 30-11-41-400-001).
(10)
Put the end of the bonding strap (109) in position on the duct box (104).
(11)
Install the screw (110), the washer (108) and the nut (107)
(Ref. TASK 20-28-00-912-004).
(12) Install the duct (94) as given before. Subtask 30-11-42-865-051
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1DL, 2DL, 5CV, 7CV.
Subtask 30-11-42-720-050
D. Test CAUTION : DO NOT USE ENGINE POWER WHEN YOU DO A LEAK TEST OF THE WING
_______ ANTI-ICE DUCTS. HOT AIR FROM THE ENGINE CAN CAUSE INJURY.
(1) Do a leak test of the wing anti-ice ducts (Ref. TASK 30-11-00-790-001).
Subtask 30-11-42-420-057
E. Complete the Installation Procedure
(1)
Use STRUCTURE PAINTS (Material No. 16-016) and paint a red line across the nuts of the clamps (22) and (53). (Ref. Fig. 402/TASK 30-11-42-991-002)
(2)
Install the applicable insulation muff(s) (1), (9), (46), (93) and
(99) and safety with the new MISCELLANEOUS (Material No. 19-001).
5. Close-up
________
Subtask 30-11-42-410-050
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the applicable access panels:
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ICE AND RAIN PROTECTION 防冰和排雨1(45)
