R No specific Torque Wrench : range 0.00 to 1.20 m.daN
R (0.00 to 9.00 lbf.ft)
B. Consumable Materials
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
Material No. 04-004 USA MIL-PRF-23827 TYPE I
SYNTH.ESTER BASED GREASE HIGH PRESSURE
(Ref. 20-31-00)
Material No. 04-022 USA MIL-PRF-81322 GRADE 2
SYNTHE.HYDROCARBON GREASE HIGH PRESSURE
(Ref. 20-31-00)
1EFF : ALL 1 32-22-13Page 430 1 1 May 01/05 1 1 1CES 1
C. Expendable Parts
-------------------------------------------------------------------------------
FIG.ITEM |DESIGNATION |IPC-CSN
-------------------------------------------------------------------------------
5 cotter pin 32-22-01 03A-030 5 cotter pin 32-22-01 03C-030 5 cotter pin 32-22-01 03D-030 6 cotter pin 32-22-01 03A-030 6 cotter pin 32-22-01 03C-030 6 cotter pin 32-22-01 03D-030 16 cotter pin 32-22-01 03A-090 16 cotter pin 32-22-01 03C-090 16 cotter pin 32-22-01 03D-090 19 cotter pin 32-22-01 03A-140 19 cotter pin 32-22-01 03C-140 19 cotter pin 32-22-01 03D-140 20 cotter pin 32-22-01 03A-090 20 cotter pin 32-22-01 03C-090 20 cotter pin 32-22-01 03D-090 23 cotter pin 32-22-01 03A-140 23 cotter pin 32-22-01 03C-140 23 cotter pin 32-22-01 03D-140
D. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
12-22-32-640-002 Lubrication of the NLG and Doors
**ON A/C 001-049, 051-099, 101-105, 151-156, 201-209,
32-22-13-991-008 Fig. 404
R **ON A/C 106-149, 157-199, 210-299, 301-399, 401-499,
32-22-13-991-008-A Fig. 404A
1EFF : ALL 1 32-22-13Page 431 1 1 Aug 01/05 1 1 1CES 1 **ON A/C ALL
3. Job Set-up
__________
Subtask 32-22-13-860-054
A. Aircraft Maintenance Configuration
(1)
In the cockpit, on the panel 400VU, make sure that the warning notice(s) is (are) in position to tell persons not to operate the landing gear control lever.
(2)
Make sure that the access platform is in position.
(3)
Make sure that the safety barriers are in position.
4. Procedure
_________
**ON A/C 001-049, 051-099, 101-105, 151-156, 201-209,
(Ref. Fig. 404/TASK 32-22-13-991-008) R **ON A/C 106-149, 157-199, 210-299, 301-399, 401-499,
(Ref. Fig. 404A/TASK 32-22-13-991-008-A)
**ON A/C 001-049, 051-099, 101-105, 151-156, 201-209,
Subtask 32-22-13-420-056
A. Installation of the Aft Door Assy
(1)
Install the bush (8) on the door (22). NOTE : Make sure that the bush (8) is in the correct position.
____
(2)
Lubricate the bolts (10) and (13) with COMMON GREASE (Material No. 04-004) or COMMON GREASE (Material No. 04-022).
NOTE : Do not mix Material No. 04-004 with Material No. 04-022. You
____ can use Material No. 04-022 as an alternative to Material No. 04-004. Clean and degrease the parts before you use Material No. 04-022.
1EFF : ALL 1 32-22-13Page 432 1 1 Aug 01/05 1 1 1CES 1
(3)
Install the bushes (15) and (7) on the fittings and keep the door
(22) in position.
(4)
Install the bolts (10) and (13) and the washers (9) and (14).
(5)
Install the nut (6), TORQUE it to 0.3 m.daN (26.54 lbf.in) and safety it with the new cotter pin (5).
(6)
Install the nut (17) , TORQUE it to 0.3 m.daN (26.54 lbf.in) and safety it with the new cotter pin (16).
(7)
Install the bolt (11), the bonding braid (12), install the nut (18) and tighten it.
(8)
Install the bolt (2), the bonding braid (3), install the nut (4) and tighten it.
(9)
Lubricate the bolt (23) with COMMON GREASE (Material No. 04-004) or COMMON GREASE (Material No. 04-022).
NOTE : Do not mix Material No. 04-004 with Material No. 04-022. You
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架4(17)
