B. Get Access
 (1)
 Open the NLG doors (Ref. TASK 32-22-00-010-001).

 (2)
 Put the access platform in position below the applicable NLG door.

 4. Procedure
_________
 **ON A/C 001-049, 051-099, 101-105, 151-199, 201-212,

 (Ref. Fig. 405/TASK 32-22-11-991-010) R **ON A/C 106-149, 213-299, 301-399, 401-499,
 (Ref. Fig. 405A/TASK 32-22-11-991-010-A)
 **ON A/C ALL

 Subtask 32-22-11-020-055
 A. Removal of the Main Door Assy
 (1) Disconnect the applicable NLG main-door control-rod NOTE : Do not change the adjustment of the control rod (1).
____
 (a) Remove the cotter pin (17) and discard it, remove the nut (16) and the washer (18).
 1EFF : ALL 1 32-22-11Page 428 1 1 Aug 01/05 1 1 1CES 1

 NLG Main Doors
 Figure 405/TASK 32-22-11-991-010

R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 32-22-11Page 429 1201-212, 1May 01/05 1 1 1CES 1

 NLG Main doors
 Figure 405A/TASK 32-22-11-991-010-A

R 1EFF : 106-149, 213-299, 301-399, 401-499, 1 32-22-11Page 430 1 1 Aug 01/05 1 1 1CES 1

 (b) Remove the bolt (20) and disconnect the rod (1).
 (2)
 Remove the nuts (2) and the bolts (8).

 (3)
 Disconnect the bonding braids (7).

 (4)
 Remove and discard the cotter pins (3) and (13), remove the nuts (4) and (14).

 (5)
 Remove the washers (5) and (12) and the bolts (6) and (10).

 (6)
 Remove the door (15).

 1EFF : ALL 1 32-22-11Page 431 1 1 Aug 01/03R 1 1 1CES 1

 TASK 32-22-11-410-001
 Installation of the Main Door Assy after Removal for Access
 1. Reason for the Job
__________________
 This procedure is only applicable when the main door assy was removed for access. For the applicable procedure to install the main door assy after replacement, Ref. TASK 32-22-11-400-001.
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------
REFERENCE  QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific safety barriers
 No specific warning notice(s)
 No specific access platform 1.7 m (5 ft. 7 in.)

R No specific  Torque Wrench : range 0.00 to 1.20 m.daN
R  (0.00 to 9.00 lbf.ft)
 B. Consumable Materials
 -------------------------------------------------------------------------------
REFERENCE  DESIGNATION
 -------------------------------------------------------------------------------
Material No. 04-022  USA MIL-PRF-81322 GRADE 2
 SYNTHE.HYDROCARBON GREASE HIGH PRESSURE
 (Ref. 20-31-00)

 Material No. 09-013  USA MIL-PRF-81733 TYPE I CLASS A
 CORROSION INHIBITING BRUSH CONSISTENCY
 (Ref. 20-31-00)

 1EFF : ALL 1 32-22-11Page 432 1 1 May 01/05 1 1 1CES 1

 C. Expendable Parts
 -------------------------------------------------------------------------------
FIG.ITEM |DESIGNATION |IPC-CSN
 -------------------------------------------------------------------------------
3 cotter pins 32-22-01 02 -010 13 cotter pin 32-22-01 02 -010 17 cotter pin 32-22-01 02 -010 17 cotter pin 32-22-11 01A-180 17 cotter pin 32-22-11 01B-180 19 bush 32-22-11 01A-220 19 bush 32-22-11 01B-220
 D. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
12-22-32-640-002 Lubrication of the NLG and Doors
 32-22-00-010-001 Nose Gear Doors - Ground Doors Opening
 32-22-00-410-001 Nose Gear Doors - Ground Doors Closing

 **ON A/C 001-049, 051-099, 101-105, 151-199, 201-212,
 32-22-11-991-010 Fig. 405
R **ON A/C 106-149, 213-299, 301-399, 401-499,
 32-22-11-991-010-A Fig. 405A
 **ON A/C ALL
 3. Job Set-up
__________
 Subtask 32-22-11-860-052
 A. Aircraft Maintenance Configuration
 (1) In the cockpit, on the panel 400VU, make sure that the warning notice(s) is (are) in position to tell persons not to operate the landing gear control lever.
 1EFF : ALL 1 32-22-11Page 433 1 1 Aug 01/05 1 1 1CES 1

 (2)
 Make sure that the safety barriers are in position.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架4(8)