__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific access platform 2.0 m (6 ft. 7 in.)
1EFF : ALL 1 33-34-11Page 301 1 1 Feb 01/00R 1 1 1CES 1
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
33-34-00-710-001 Operational Test of the FWD and AFT Cargo Compartment Lighting 52-30-00-860-001 Open the FWD or AFT Cargo-Compartment Door with the Yellow Electric Pump 52-30-00-860-002 Close the FWD or AFT Cargo-Compartment Door with the Yellow Electric Pump
**ON A/C 001-049, 051-099, 101-149, 201-299,
33-34-11-991-002 Fig. 301
R **ON A/C 151-199, 401-499,
33-34-11-991-002-A Fig. 301A
**ON A/C 301-399,
33-34-11-991-002-B Fig. 301B
**ON A/C ALL
3. Job Set-up
__________
Subtask 33-34-11-865-053
A. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------
PANEL SERVICE IDENT. LOCATION
-------------------------------------------------------------------------------
2000VU LIGHT - CARGO COMPT - FWD 1LU J06
2000VU LIGHT - CARGO COMPT - AFT 2LU J07
Subtask 33-34-11-010-052
B. Get Access
(1)
Put an access platform in position at the FWD and/or AFT cargo-compartment door 825, 826.
(2)
Open the FWD and/or AFT cargo-compartment door and install the actuator safety-locks (Ref. TASK 52-30-00-860-001).
4. Procedure
_________
**ON A/C 001-049, 051-099, 101-149, 201-299,
(Ref. Fig. 301/TASK 33-34-11-991-002) R **ON A/C 151-199, 401-499,
(Ref. Fig. 301A/TASK 33-34-11-991-002-A)
**ON A/C 301-399,
(Ref. Fig. 301B/TASK 33-34-11-991-002-B)
**ON A/C ALL
Subtask 33-34-11-020-053
A. Removal of the Fluorescent Lamp
(1)
Release the quick-release fasteners (1) around the glass cover (2).
(2)
Remove the glass cover (2) from the lamp housing (6).
(3)
Push the buttons (4) at each end of the lampholder (5).
(4)
Remove and discard the fluorescent lamp (3).
Ballast Unit with Lampholder
Figure 301/TASK 33-34-11-991-002
R 1EFF : 001-049, 051-099, 101-149, 201-299, 1 33-34-11Page 304 1 1 May 01/05 1 1 1CES 1
Ballast Unit with Lampholder
Figure 301A/TASK 33-34-11-991-002-A
R 1EFF : 151-199, 401-499, 1 33-34-11Page 305 1 1 Aug 01/05 1 1 1CES 1
R Ballast Unit with Lampholder
R Figure 301B/TASK 33-34-11-991-002-B
R 1EFF : 301-399, 1 33-34-11 Page 306
1 1 May 01/04
1 1
1CES 1
Subtask 33-34-11-420-051
B. Installation of the Fluorescent Lamp
(1)
Clean the component interface and/or the adjacent area.
(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Replace the fluorescent lamp (3).
(4) Install the glass cover (2) to the lamp housing (6). Subtask 33-34-11-865-054
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1LU and 2LU.
5. Close-up
________ Subtask 33-34-11-710-051
A. Do an operational test of the FWD and AFT cargo compartment lighting (Ref. TASK 33-34-00-710-001).
Subtask 33-34-11-410-051
B. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the actuator safety-locks and close the FWD and/or AFT cargo-compartment door (Ref. TASK 52-30-00-860-002).
(3)
Remove the access platform(s).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LIGHTS 燈光1(117)
