(2)
Install the wingtip glazing panel (1) (Ref. TASK 57-37-12-400-001).
Subtask 33-41-11-942-050
C. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Remove the warning notice(s).
(3)
Remove the access platform(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
TASK 33-41-11-000-002 R Removal of the Lamp in the Wingtip Navigation Light WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
R No specific lint-free cloth No specific safety barriers No specific warning notice No specific access platform 4.0 m (13 ft. 1 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
57-37-12-000-001 Removal of the Navigation Light Glazing Panel 3. Job Set-up
__________
Subtask 33-41-11-941-051
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Put a warning notice in position on the panel 25VU to tell persons not to operate the strobe lights or the navigation lights.
Subtask 33-41-11-865-055
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------122VU LIGHTING/EXT LT/NAV1/AND LOGO/LT 1LA T03 122VU LIGHTING/EXT LT/NAV2/AND LOGO/LT 2LA T02 122VU LIGHTING/WING/STROBE 10LV V05
Subtask 33-41-11-010-053
C. Get Access
(1)
Put the access platform below applicable zone 534 or 634.
(2)
Remove the wingtip glazing panel (Ref. TASK 57-37-12-000-001).
4. Procedure
_________ Subtask 33-41-11-020-051-A R A. Removal of the Wingtip Navigation-Light Lamp CAUTION : DO NOT TOUCH THE LAMP GLASS WITH YOUR FINGERS.
_______ THE OILS FROM YOUR SKIN WILL QUICKLY CAUSE DETERIORATION OF THE LAMP. IF YOU ACCIDENTALLY TOUCH THE LAMP GLASS, CLEAN IT WITH A LINT-FREE CLOTH.
CAUTION : DO NOT USE NON APPROVED METAL TOOLS TO REMOVE THE LAMP FROM THE
_______ LAMP HOLDER. THESE METAL TOOLS CAN CAUSE DAMAGE TO THE LAMP REFLECTOR AND THE LAMP HOLDER.
R CAUTION : DO NOT APPLY TOO MUCH FORCE TO THE BULB OR SOCKET CONTACTS. TOO_______
R MUCH FORCE CAN CAUSE PERMANENT DEFORMATION OF THE SOCKET, AND
R AS A RESULT, ARCING AND THUS BULB FAILURE.
R NOTE : This procedure is applicable to one and two-lamp wingtip____
R navigation lights.
R (1) Release the clips that hold the glass of the navigation light in
R position and then remove the glass.
R (2) Use a lint-free cloth to carefully remove the lamp from the
R navigation light as follows:
R (a) Carefully push the bulb vertically up (or down) to release the
R lower (or higher) location spigot.
R (b) Carefully pull and remove the lamp from the lamp socket.
R NOTE : To remove the lamp without damage, you can pull the ends____
R of a piece of string or a cable tie put around the lamp.
TASK 33-41-11-400-002
Installation of the Lamp in the Wingtip Navigation Light
WARNING : MAKE SURE THAT THE FLIGHT CONTROL SAFETY-LOCKS AND THE WARNING
_______
NOTICES ARE IN POSITION.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM LIGHTS 燈光1(145)
