B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
33-41-15-000-001 Removal of the Tail Navigation Light 15LA
1EFF : ALL 1 33-41-00Page 413 1 1 Feb 01/01R 1 1 1CES 1
3. Job Set-up
__________ Subtask 33-41-00-941-054
A. Safety Precautions WARNING : DO NOT TOUCH THE APU UNTIL IT IS SUFFICIENTLY COOL TO PREVENT
_______
BURNS WHEN YOU DO THE MAINTENANCE TASK(S).
(1)
Put the safety barriers in position.
(2)
Put a warning notice in the cockpit to tell persons not to operate the tail navigation light.
(3)
Put a warning notice in position to tell persons not to operate the APU.
Subtask 33-41-00-941-052
B. Get Access
(1) Put the access platform at the APU tail-cone exhaust area Zone 317. Subtask 33-41-00-865-056
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
121VU APU/APU/CTL 2KD L42 121VU APU/ECB/SPLY 1KD L41 122VU LIGHTING/EXT LT/NAV1/AND LOGO/LT 1LA T03 122VU LIGHTING/EXT LT/NAV2/AND LOGO/LT 2LA T02
4. Procedure
_________ Subtask 33-41-00-040-051
A. Deactivation of the Lens of the Tail Navigation Light
(1)
Remove the lens only (Ref. TASK 33-41-15-000-001).
(2)
Write a note in the aircraft technical log that the lens has been deactivated.
1EFF : ALL 1 33-41-00Page 414 1 1 Feb 01/01R 1 1 1CES 1
5. Close-up
________ Subtask 33-41-00-865-057
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 2KD, 1KD, 1LA, 2LA.
Subtask 33-41-00-942-052
B. Removal of Equipment
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the safety barriers.
(3)
Remove the warning notice(s).
(4)
Remove the access platform(s).
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 33-41-00Page 415 1 1 Feb 01/01R 1 1 1CES 1
TASK 33-41-00-440-002
Reactivation of the Lens of the Tail Navigation Light
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1. Reason for the Job
__________________
Refer to the CDL TASK: 33-3
Rear navigation light lens (glazing)
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notice
No specific access platform 4.5 m (14 ft. 9 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
33-41-15-400-001 Installation of the Tail Navigation Light 15LA
1EFF : ALL 1 33-41-00Page 416 1 1 Feb 01/01R 1 1 1CES 1
3. Job Set-up
__________
Subtask 33-41-00-941-055
A. Safety Precautions WARNING : DO NOT TOUCH THE APU UNTIL IT IS SUFFICIENTLY COOL TO PREVENT
_______
BURNS WHEN YOU DO THE MAINTENANCE TASK(S).
(1)
Put the safety barriers in position.
(2)
Put a warning notice in the cockpit to tell persons not to operate the tail navigation light.
(3)
Put a warning notice in position to tell persons not to operate the APU.
Subtask 33-41-00-941-053
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LIGHTS 燈光1(141)
