(3)
Make sure that the light SW 11LJ is set to the ON position.
4. Procedure
_________ (Ref. Fig. 401/TASK 49-41-41-991-001) Subtask 49-41-41-020-050
A. Removal of the Igniter Plug (8031KM) WARNING : DISCONNECT THE LOW TENSION ELECTRICAL SUPPLY 5 MINUTES BEFORE
_______ YOU START WORK ON THE IGNITION SYSTEM. ALSO, GROUND THE IGNITER LEAD WITH AN INSULATED DEVICE AS YOU DISCONNECT IT FROM THE IGNITER PLUG. HIGH CURRENT AND VOLTAGE, WHICH ARE USED IN THE IGNITION SYSTEM, CAN KILL YOU.
NOTE : There is only one igniter plug. It is installed in the combustion
____
casing at 220 degrees viewed from the rear.
(1)
Remove and discard the lockwire from the electrical connector (1).
(2)
Disconnect the electrical connector (1).
(3)
Remove and discard the lockwire from the ignition electrical lead (2).
(4)
Disconnect the ignition electrical lead (2) from the igniter plug (8031KM) (3).
(5)
Remove the igniter plug (8031KM) (3) and the gasket (4).
(6)
Put blanking caps on the disconnected electrical connectors.
Igniter Plug.
Figure 401/TASK 49-41-41-991-001
CES TASK 49-41-41-400-001 Installation of the Igniter Plug (8031KM) (GTCP 36-300) WARNING : DO NOT TOUCH THE APU UNTIL IT IS SUFFICIENTLY COOL TO PREVENT BURNS
_______ WHEN YOU DO THE MAINTENANCE TASK(S).
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific Torque Wrench : range 0.00 to 1.20 m.daN
(0.00
to 9.00 lbf.ft) No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft)
B.
Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
No specific lockwire-corrosion resistant steel Material No. 04-014 USA MIL-PRF-907 HIGH TEMPERATURECOMPOUND (Ref. 20-31-00)
C. Expendable Parts
-------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
3 igniter plug 49-41-04 01 -050B 4 gasket 49-41-04 01 -060
D. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-42-00-861-001 Energize the Ground Service Network from the External Power 24-42-00-862-001 De-energize the Ground Service Network Supplied from the External Power 29-00-00-864-001 Put the Related Hydraulic System in the Depressurized Configuration before Maintenance Action 29-14-00-614-002 Pressurization of the Hydraulic Reservoirs through
the Ground Connector 49-00-00-710-004 Operational Test of the APU (4005KM) (GTCP 36-300) 52-41-00-010-001 Open the APU Doors for Access 52-41-00-410-001 Close the APU Doors after Access 49-41-41-991-001 Fig. 401
3. Job Set-up
__________
Subtask 49-41-41-860-056
A. Aircraft Maintenance Configuration
(1)
Make sure that the ground service network is energized (Ref. TASK 24-42-00-861-001).
(2)
On the panel 25VU make sure that the APU MASTER SW pushbutton switch is off.
(3)
Make sure that there is a warning notice in the cockpit to tell persons not to start the APU.
(4)
Make sure that hydraulic systems are depressurized
(Ref. TASK 29-00-00-864-001).
(5)
Make sure that the access platform is in position below the APU compartment.
(6)
Make sure that the APU access doors 315AL and 316AR are open (Ref. TASK 52-41-00-010-001).
(7)
Make sure that the LIGHT SW 11LJ is set to the ON position
(8)
Make sure that the igniter leads are grounded with an insulated device.
(9)
Make sure that the LT supply P10 connector is disconnected. Subtask 49-41-41-865-051
B.
Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU APU/APU/CTL 2KD L42 121VU APU/ECB/SPLY 1KD L41
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 機載輔助動力 AIRBORNE AUXILIARY POWER4(75)
