R EFF : 001-049, 101-105, 107-107, 151-199, 49-16-41Page 408 201-210, Config-2 Aug 01/05
CES
DIVERTER - REMOVAL/INSTALLATION
_______________________________ TASK 49-16-41-000-004 Removal of the fixed APU Diverter (APS 3200)
1.
Reason for the Job
__________________
Self explanatory.
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific non-metallic scraper
No specific access platform 2.5 m (8 ft. 2 in.)
No specific access platform 3.5 m (11 ft. 6 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-42-00-861-001 Energize the Ground Service Network from the External
Power 29-14-00-614-001 Depressurization of the Hydraulic Reservoirs 49-16-43-000-002 Removal of the Air Intake Flap (APS 3200) 52-41-00-010-001 Open the APU Doors for Access 49-16-41-991-005 Fig. 401
3. Job Set-up
__________ Subtask 49-16-41-860-059
A. Aircraft Maintenance Configuration
(1)
Put the warning notices on panel 25VU to tell persons not to start the APU.
(2)
Energize the ground service network
(Ref. TASK 24-42-00-861-001).
(3)
Make sure that the hydraulic systems are depressurized (Ref. TASK 29-
14-00-614-001). Subtask 49-16-41-010-058
B. Get Access
(1)
Put the access platform below the access doors 312AR.
(2)
Open the access door 312AR.
(3)
Set the LIGHT control switch 3LJ to the ON position.
(4)
Put the access platform below the APU access doors 315AL, 316AR and the maintenance door 314AR.
(5)
Open the maintenance door 314AR.
(6)
Open the APU access doors 315AL, 316AR (Ref. TASK 52-41-00-010-001).
(7)
Set the LIGHT control swtich 11LJ to the ON position.
(8)
Remove the air intake flap (Ref. TASK 49-16-43-000-002) Subtask 49-16-41-865-069
C.
Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU APU/APU/CTL 2KD L42 121VU APU/ECB/SPLY 1KD L41
4. Procedure
_________
(Ref. Fig. 401/TASK 49-16-41-991-005) Subtask 49-16-41-020-053
A. Removal of the fixed Diverter
(1)
Remove the sealant from the screws (1) and washers (2) with a non-metallic scraper.
(2)
Remove the screws (1) and the washers (2).
(3)
Remove the nuts (5), the washers (6) and the screws (4).
(4)
Remove the screws (7) and the washers (8).
(5)
Remove the screws (9) and the washers (10), (11).
(6)
Remove the sealant around the fixed diverter (12) with a non-metallic scraper.
(7)
Remove the fixed diverter (12) and the shim (3).
Fixed Diverter
Figure 401/TASK 49-16-41-991-005
CES
TASK 49-16-41-400-004
Installation of the fixed APU Diverter (APS 3200)
WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK AREA WHEN
_______ YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
1. Reason for the Job
__________________
Self explanatory.
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 機載輔助動力 AIRBORNE AUXILIARY POWER3
