「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : 401-499, ∞∞24-22-00∞∞∞∞∞∞∞∞∞∞Page 267
 Aug 01/05 CES

R  B. If the BITE test gives the message TEST PASSED: 
R  - do a check of the wiring (Ref. ASM 24-22/03) for an open circuit 
R  between: 
R  . pin 2 of the ELEC/GCU2 circuit breaker (2XU2) and pin B/18 of the GLC 
R  2 (9XU1) 
R  . pin B/20 of the GLC 2 and pin A/30 of the diode module 2420VD 
R  . pin A/15 of the diode module 2420VD and pin A/6A of the GCU 2. 
R  - do a check of the contact of the GLC 2 (9XU2) for correct operation 
R  between pins B/18 and B/20 (Ref. ASM 24-22/03). 
R  (1) If the wiring or the contact are not correct: 
R  - repair or replace the wiring as necessary 
R  - replace the GLC-2 (9XU2) (Ref. AMM TASK 24-22-55-000-001) and (Ref. 
R  AMM TASK 24-22-55-400-002) as necessary. 
R  (2) If the wiring or the contact are correct: 
R  - replace the GCU-2 (1XU2) (Ref. AMM TASK 24-22-34-000-001) and (Ref. 
R  AMM TASK 24-22-34-400-001). 
R  C. Do the test given in para. 3.

R TASK 24-22-00-810-825

R Failure of the GLC 1 Status Indication R 1. Possible Causes
_______________
R - GCU-1 (1XU1) R - GLC-1 (9XU1) R - wiring
R 2. Job Set-up Information
______________________
R A. Referenced Information
R -------------------------------------------------------------------------------R REFERENCE DESIGNATION R -------------------------------------------------------------------------------
R AMM 24-22-34-000-001 R AMM 24-22-34-400-001 R AMM 24-22-55-000-001 R AMM 24-22-55-400-002 R R AMM 24-41-00-740-002 R ASM 24-22/02
R 3. Fault Confirmation
__________________
R A. Test
Removal of the GCU-1(2) (1XU1, 1XU2)
Installation of the GCU-1(2) (1XU1, 1XU2)
Removal of the Contactors (9XU1, 9XU2, 11XU1, 11XU2)
Installation of the Contactors (9XU1, 9XU2, 11XU1,
11XU2)
Operational Check of GAPCU via CFDS

R (1) Do the BITE test of the GAPCU (Ref. AMM TASK 24-41-00-740-002).

R (a) If the BITE test gives the message TEST FAILED:
R - do the trouble shooting given in Para 4.A.
R (b) If the BITE test gives the message TEST PASSED:

R - do the trouble shooting given in Para 4.B. R 4. Fault Isolation
_______________
R A. If the BITE test gives the message TEST FAILED:
R - push the line key adjacent to the TEST FAILED message.

R (1) If the maintenance message GCU1 (1XU1) comes into view:
R - replace the GCU-1 (1XU1) (Ref. AMM TASK 24-22-34-000-001) and (Ref.
R AMM TASK 24-22-34-400-001).

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : 401-499, ∞∞24-22-00∞∞∞∞∞∞∞∞∞∞Page 269
 Aug 01/05 CES

R  B. If the BITE test gives the message TEST PASSED: 
R  - do a check of the contact for correct operation of the GLC 1 (9XU1) 
R  between pins B/18 and B/20 of the GLC 1 (Ref. ASM 24-22/02). 
R  (1) If the contact does not operate correctly: 
R  - replace the GLC-1 (9XU1) (Ref. AMM TASK 24-22-55-000-001) and (Ref. 
R  AMM TASK 24-22-55-400-002) as necessary. 
R  (2) If the contact operates correctly: 
R  - do a check of the wiring of the GLC 1 sense circuit (Ref. ASM 24-
R  22/02) for an open circuit between: 
R  . pin 2 of the ELEC/GCU1 circuit breaker (2XU1) and pin A/B of the 
R  function relay (20XU) 
R  . pin A/3 of the function relay and pin B/18 of the GLC 1 (9XU1) 
R  . pin B/20 of the GLC 1 and pin A/29 of the diode module 2420VD 
R  . pin A/14 of the diode module 2420VD and pin A/6A of the GCU 1. 
R  (a) If the wiring is not correct: 
R  - repair or replace as necessary. 
R  (b) If the wiring is correct: 
R  - replace the GCU-1 (1XU1) (Ref. AMM TASK 24-22-34-000-001) and 
R  (Ref. AMM TASK 24-22-34-400-001). 
R  C. When you replace a component or repair the wiring: 
R  - do the subsequent flight before you do the check of the Class 3 Faults 
R  of the GAPCU from the CFDS to make sure that the system operates 
R  correctly. 
R  If the test continues to give the fault message, continue the trouble 
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 電源 3(2)