- wiring from the SEC1 (1CE1) COM part to the SEC1 MON part
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R AMM 27-34-51-000-001 Removal of the Elevator Servo Control
AMM 27-34-51-000-005 Removal of the Elevator Servo Control Actuator R Solenoid Valve R AMM 27-34-51-400-001 Installation of the Elevator Servo Control
AMM 27-34-51-400-004 Installation of the Elevator Servo Control Actuator
R Solenoid Valve AMM 27-94-34-000-001 Removal of the SEC (1CE1,1CE2,1CE3) AMM 27-94-34-400-001 Installation of the SEC (1CE1,1CE2,1CE3) AMM 27-96-00-710-020 Operational Test of the Side Stick Assembly
(Activation for the BITE Test)
AMM 27-96-00-740-001 BITE Test of the EFCS (Ground Scanning)
ASM 27-94/07
3. Fault Confirmation
__________________
A. Test
(1) Do the operational test of the side stick assembly (Activation for the BITE test) (Ref. AMM TASK 27-96-00-710-020).
NOTE : Before you start the operational test procedure, release the
____ FLT CTL/ELAC 1, FLT CTL/ELAC 2 and FLT CTL/SEC 2 pushbutton switches (on these pushbutton switches the OFF legends come on).
(2) Do the BITE test of the EFCS (ground scanning) (Ref. AMM TASK 27-96-00-740-001).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-30-00∞∞∞∞∞∞∞∞∞∞Page 240
Aug 01/03 CES
4. Fault Isolation
_______________
A. If the test gives the maintenance message:
SEC1 MON OR WIRING TO L G ELEV SOL VLV 34CE1
(1) Remove the SEC1 (Ref. AMM TASK 27-94-34-000-001).
(2) At the SEC1 receptacle, do a check of the resistance between the pin AB/14D and the pin AE/14G (Ref. ASM 27-94/07).
NOTE : The resistance must be between 40 and 100 Ohms.
____
(a) If the resistance is less than 40 Ohms:
- at the inboard elevator servocontrol (34CE1), do a check of the resistance of the solenoid valve between the pin C/J and the pin C/U (Ref. ASM 27-94/07).
NOTE : The resistance must be between 40 and 100 Ohms.
____
1 If the resistance values are out of the specified limits:
_ a Replace the solenoid valve of the servocontrol 34CE1 (Ref.
_ AMM TASK 27-34-51-000-005) and (Ref. AMM TASK 27-34-51-400-004).
b Do again a check of the resistance of the solenoid valve
_ between the pin C/J and the pin C/U of the inboard elevator servocontrol (34CE1) (40 to 100 Ohms).
- If the resistance values are out of the specified limits: . Replace the SERVO CTL-L ELEVATOR, INBD G (34CE1) (Ref. AMM TASK 27-34-51-000-001) and (Ref. AMM TASK 27-34-51-400-001). . Replace the SEC-1 (1CE1) (Ref. AMM TASK 27-94-34-000-001) and (Ref. AMM TASK 27-94-34-400-001).
- If the resistance values are in the specified limits: Replace the SEC-1 (1CE1) (Ref. AMM TASK 27-94-34-000-001) and (Ref. AMM TASK 27-94-34-400-001).
2 If the resistance values are in the specified limits:
_ a Repair the wiring of the SOL VLV2 signal from the
_ servocontrol (34CE1) to the SEC1 (1CE1), from the pin C/J to the pin AB/14D and from the pin C/U to the pin AE/14G (Ref. ASM 27-94/07):
b Replace the SEC-1 (1CE1) (Ref. AMM TASK 27-94-34-000-001)
_ and (Ref. AMM TASK 27-94-34-400-001).
(b) If the resistance is more than 100 Ohms:
- at the inboard elevator servocontrol (34CE1), do a check of the resistance of the solenoid valve between the pin C/J and the pin C/U (Ref. ASM 27-94/07).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-30-00∞∞∞∞∞∞∞∞∞∞Page 241
Aug 01/00R CES
____
1 If the resistance values are out of the specified limits:
_ a Replace the solenoid valve of the servocontrol 34CE1 (Ref.
_ AMM TASK 27-34-51-000-005) and (Ref. AMM TASK 27-34-51-400-004).
b Do again a check of the resistance of the solenoid valve
_ between the pin C/J and the pin C/U of the inboard elevator servocontrol (34CE1) (40 to 100 Ohms).
- If the resistance values are out of the specified limits: . Replace the SERVO CTL-L ELEVATOR, INBD G (34CE1) (Ref. AMM TASK 27-34-51-000-001) and (Ref. AMM TASK 27-34-51-400-001). . Install the SEC1 (Ref. AMM TASK 27-94-34-400-001).
- If the resistance values are in the specified limits: Install the SEC1 (Ref. AMM TASK 27-94-34-400-001). 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 飛行操縱 1(51)
