曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R -------------------------------------------------------------------------------R REFERENCE QTY DESIGNATION R -------------------------------------------------------------------------------
R No specific standard locking bolt R 0U190360 1 PIN - RIGGING R 98D27403000000 1 HOLDING TOOL-TRIM CTL LOWER SHAFT
R B. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
R ISB 27-1164 R AMM 27-41-00-210-001 R R AMM 27-41-00-210-002 R R AMM 27-41-00-210-003 R R AMM 27-41-00-220-001 R R AMM 27-41-00-720-001 R R AMM 27-41-00-730-001 R AMM 27-41-41-000-001 R AMM 27-41-41-400-001 R AMM 27-41-42-000-001 R AMM 27-41-42-400-001 R AMM 27-41-43-000-001 R R AMM 27-41-43-400-001 R R AMM 27-41-44-000-001 R AMM 27-41-44-400-001
AMM 27-44-51-000-001 Detailed Visual Inspection of the THS Mechanical Control Visual Inspection of the Pitch-Trim Control Wheel Indicators Visual Inspection and Lubrication of the Rear THS control cable (between FR71 and the THS actuator) Check of the Cable Tension Regulator of the THS Trim Control (Pointer in the Limits) Functional Test of the THS-Actuator Overtravel Related to the Mechanical Indicator System Test of the THS Actuator Electrical Control Removal of the Control Mechanism-Pitch Trim Installation of the Control Mechanism-Pitch Trim Removal of the Cable Tension Regulator Installation of the Cable Tension Regulator Removal of the Pitch Trim Control Stop and Gearset Unit Installation of the Pitch Trim Control Stop and Gearset Unit Removal of the THS Control Cables Installation of the THS Control CablesRemoval of the Trimmable Horizontal Stabilizer (THS) Actuator (9CE) -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------

 

AMM  27-44-51-400-001 
AMM  27-44-57-000-001 
AMM  27-44-57-400-001 
AMM  27-96-00-710-022 
R R R  AMM 27-96-00-740-001 AMM 53-59-00-210-001 27-40-00-991-001 
3. Fault Confirmation__________________ 
R  A. Not Applicable
 4. Fault Isolation_______________ 

Installation of the Trimmable Horizontal Stabilizer (THS) Actuator (9CE)Removal of the Pitch Trim Actuator from the THS Actuator 9CEInstallation of the Pitch Trim Actuator to the THS Actuator 9CEOperational Test of the THS Actuator Electrical Control (Activation for BITE Test)BITE Test of the EFCS (Ground Scanning) Operational Check of Single Drain Pipe Aft of FR70 from Outside Fig. 201
R A. Inspection of the upper and lower attachments of the THS actuator:
R (1) Do an inspection of the integrity of the load path (primary and R secondary) at the lower attachment of the THS actuator (Ref. ISB 27-R 1164):
R (a) If the result of the inspection is not satisfactory:
 - replace the ACTUATOR-THS (9CE), (Ref. AMM TASK 27-44-51-000-001) and (Ref. AMM TASK 27-44-51-400-001).
R (b) If the result of the inspection is satisfactory:
R 1_ Do the operational test of the THS actuator electrical controlR (Ref. AMM TASK 27-96-00-710-022).
R NOTE : Keep the Green and the Yellow hydraulic systems
____ R pressurized.
R 2_ Do the BITE test of the EFCS (ground scanning) (Ref. AMM TASKR 27-96-00-740-001).
R NOTE : Keep the Green and the Yellow hydraulic systems
____ R pressurized.
R a_ If the BITE test gives the maintenance messages:R THS ACTR POS ERROR 9CE OF ELAC2 R THS ACTR POS ERROR 9CE OF ELAC1 R THS ACTR POS ERROR 9CE OF SEC2 R - do the step 4.B.
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-40-00∞∞∞∞∞∞∞∞∞∞Page 216
 Aug 01/05 CES

 

R  b_  If the BITE test does not give maintenance messages:
R  - no maintenance action is necessary. 
R  B. Do a functional test of the THS actuator overtravel related to the 
R  mechanical indicator (Ref. AMM TASK 27-41-00-720-001): 
R  NOTE : Keep the Green and the Yellow hydraulic systems pressurized.____ 
R  (1) If you do not find stiffness: 
R  - depressurized the Green and the Yellow hydraulic systems and do the 
R  step 4.C. 
R  (2) If you find stiffness: 
R  (a) Make sure that there is no water or ice in the lower area of the 
R  tail cone. 
R  1_  If you find water or ice, remove it and make sure that the
R  drain tube is not clogged (Ref. AMM TASK 53-59-00-210-001). 
R  (b) Disconnect the shaft (2) from the THS actuator (1) (see detail 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 飛行操縱 1(77)