3. Fault Confirmation
__________________
A. Job Set-up
Aircraft Maintenance Configuration
(1) Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-40-00∞∞∞∞∞∞∞∞∞∞Page 227
Aug 01/05 CES
(2) Do the EIS start procedure (Upper ECAM DU and lower ECAM DU only) (Ref. AMM TASK 31-60-00-860-001).
(3) Pressurize the aircraft hydraulic systems (Ref. AMM TASK 29-24-00-863-001) (Ref. AMM TASK 29-23-00-863-001).
(4) On the overhead panel 23VU:
- make sure that the FLT CTL/ELAC1 and FLT CTL/SEC1 pushbutton switches are pushed (the OFF legends of these pushbutton switches are off).
(5) On the overhead panel 24VU:
- make sure that the FLT CTL/ELAC2 and FLT CTL/SEC2 pushbutton switches are pushed (the OFF legends of these pushbutton switches are off).
B. Test
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On the center pedestal: On the SD:
- move the pitch-trim control - the PITCH TRIM Indicator shows: wheels in the nose-up direction 13.5 +0.4 -0.6 deg. to the mechanical stop.
2. On the center pedestal: On the SD:
- move the pitch-trim control - the PITCH TRIM Indicator shows: wheels in the nose-down 4 +0.3 -0.5 deg.. direction to the mechanical stops.
4. Fault Isolation
_______________
A. On the SD, the THS position is in the tolerances:
(1) Install the TOOL - ZERO POSITIONING, THS ACTUATOR (0U190834) on the screw jack of the THS actuator.
(2) Install the PIN - RIGGING (0U190360) on the input lever of the THS actuator.
(3) Do the adjustment of the THS control cables (Ref. AMM TASK 27-41-00-820-002).
(4) If the fault continues:
- remove and install in the correct position the pitch-trim control mechanism (Ref. AMM TASK 27-41-41-000-001) and (Ref. AMM TASK 27-41-41-400-001).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-40-00∞∞∞∞∞∞∞∞∞∞Page 228
Aug 01/05 CES
(5) Remove the TOOL - ZERO POSITIONING, THS ACTUATOR (0U190834) and the PIN - RIGGING (0U190360).
B. On the SD, the THS position is out of the tolerances:
(1) Install the TOOL - ZERO POSITIONING, THS ACTUATOR (0U190834) on the screw jack of the THS actuator.
(2) Install the PIN - RIGGING (0U190360) on the input lever of the THS actuator.
(3) Do the adjustment of the THS zero position (Ref. AMM TASK 27-41-00-820-001).
(4) Do the adjustment of the THS control cables (Ref. AMM TASK 27-41-00-820-002).
(5) Remove and install in the correct position the pitch-trim control mechanism (Ref. AMM TASK 27-41-41-000-001) and (Ref. AMM TASK 27-41-41-400-001).
(6) If the fault continues:
- replace the ACTUATOR-THS (9CE) (Ref. AMM TASK 27-44-51-000-001) and (Ref. AMM TASK 27-44-51-400-001)
(7) Remove the TOOL - ZERO POSITIONING, THS ACTUATOR (0U190834) and PIN -RIGGING (0U190360)
C. Test Do the test given in Para. 3.
Mechanical Latched Indicator R Figure 202/TASK 27-40-00-991-002
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-40-00∞∞∞∞∞∞∞∞∞∞Page 230
Aug 01/05 CES
FLAPS ELECTRICAL CONTROL AND MONITORING - FAULT ISOLATION PROCEDURES
____________________________________________________________________
TASK 27-51-00-810-802
R R SFCC - FLAP PCU VALVEBLOCK Fault
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU_______ START A TASK ON OR NEAR: - THE FLIGHT CONTROLS - THE FLIGHT CONTROL SURFACES - THE LANDING GEAR AND THE RELATED DOORS - COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROL SURFACES ARE_______ CLEAR BEFORE YOU PRESSURIZE/DEPRESSURIZE A HYDRAULIC SYSTEM.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 飛行操縱 1(82)
