曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

REFERENCE  DESIGNATION
 -------------------------------------------------------------------------------
05-50-00-810-801 Identification of the Cause of In-Flight Airframe Vibrations and/or Noises AMM 27-34-00-200-001 Check of the Elevator Servo Controls and Hinge Bearings for too much Play and Condition
 AMM 27-34-00-820-003  Adjustment of the Elevator and Hydraulic Actuation with the Gauge-Elevator Neutral Setting (98D27309002000)
 AMM 27-34-00-820-003  Adjustment of the Elevator and Hydraulic Actuation to
 0.5 Degrees Nose-Up with the Gauge-Elevator Neutral
 Setting (98D27309006000) AMM 27-34-00-820-003 Adjustment of the Elevator and Hydraulic Actuation to
 0.5 Degrees Nose-Up with the Gauge-Elevator Neutral
 Setting (98D27309002000) R
 3. Fault Confirmation
__________________
 A. Test Make sure that the identification of the cause of the vibrations is correct (Ref. TASK 05-50-00-810-801).
 4. Fault Isolation
_______________
 A. If you feel vibrations in the rear cabin: R
R (1) do a check of the elevator servo controls and hinge bearings for too R much play and condition (Ref. AMM TASK 27-34-00-200-001). R
R (2) do a check of the adjustment of the elevator and hydraulic actuation
R  (Ref. AMM TASK 27-34-00-820-003) or (Ref. AMM TASK 27-34-00-820-003) or (Ref. AMM TASK 27-34-00-820-003).
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-30-00∞∞∞∞∞∞∞∞∞∞Page 295
 Aug 01/02 CES Elevator Damping Test Not Possible (Decoding)

 

 1. Possible Causes

_______________

 2. Job Set-up Information

______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-30-00-810-848 Elevator Damping Test not Possible
 AMM 27-96-00-710-008 Operational Test of the Damping Measurement

 (Elevator)
 27-30-00-991-002 Fig. 202
 27-30-00-991-003 Fig. 203

 3. Fault Confirmation
__________________
 A. Test
 (1) Do the operational test of the damping measurement (elevator) (Ref. AMM TASK 27-96-00-710-008). (Ref. Fig. 202/TASK 27-30-00-991-002)
 4. Fault Isolation
_______________
 A. If the message ELEV TEST NOT POSSIBLE is shown on the MCDU associated to:
 (1) Code of normal engagement conditions (code: 03FF):

 - do the trouble shooting procedure (Ref. TASK 27-30-00-810-848).

 (2) Another code (different of 03FF):

 - do the decoding procedure
 (Ref. Fig. 203/TASK 27-30-00-991-003)

R B. Do the test given in para. 3.

 

R MCDU Procedure of the Elevator Damping Test Figure 202/TASK 27-30-00-991-002
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-30-00∞∞∞∞∞∞∞∞∞∞Page 297
 May 01/04 CES

 

R Decoding Table of the Elevator Damping Test Not Possible Figure 203/TASK 27-30-00-991-003
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-30-00∞∞∞∞∞∞∞∞∞∞Page 298
 May 01/04 CES Operational Test of the Damping Measurement (Elevator) not OK

 

 1. Possible Causes
_______________
 - elevator servocontrol
 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
R AMM 27-34-51-000-001 Removal of the Elevator Servo Control R AMM 27-34-51-400-001 Installation of the Elevator Servo Control AMM 27-96-00-710-008 Operational Test of the Damping Measurement (Elevator)
 3. Fault Confirmation
__________________
 A. Test Do the operational test of the damping measurement (elevator) (Ref. AMM TASK 27-96-00-710-008).
 4. Fault Isolation
_______________
 A. If the damping factor in the down or in the up position is less than 0,25:
 - replace the related elevator servocontrol (34CE1 or 34CE2 or 34CE3 or 34CE4) (Ref. AMM TASK 27-34-51-000-001) and (Ref. AMM TASK 27-34-51-400-001) .
 B. Do the test given in Para. 3.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 飛行操縱 1(71)