曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R  A): 
R  (Ref. Fig. 201/TASK 27-40-00-991-001) 
R  1_  Put the pitch-trim control wheel in the zero position.
R  2_  Put the PIN - RIGGING (0U190360) (8) in position on the THS
R  actuator (1). 
R  3_  Disconnect the mechanical system link-plate (7) from the input
R  lever (9). 
R  4_  Move the pitch-trim control wheel from one stop to the other
R  and go back to the neutral position: 
R  - if you do not find stiffness, replace the ACTUATOR-THS (9CE) 
R  (Ref. AMM TASK 27-44-51-000-001) and (Ref. AMM TASK 27-44-
R  51-400-001). 
R  - if you find stiffness, do this step: 
R  (c) Disconnect the shaft (4) from the stop and gearset unit (5) (see 
R  detail B): 
R  1_  Install the HOLDING TOOL-TRIM CTL LOWER SHAFT (98D27403000000)
R  on the drive shaft (4). 
R  2_  Install the standard locking bolt (10) on the chain (11).
R  3_  Remove the tapered pin (12).
R  4_  Move the pitch-trim control wheel from one stop to the other
R  and go back to the neutral position: 
R  - if you do not find stiffness, go to Para. (e).

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-40-00∞∞∞∞∞∞∞∞∞∞Page 217
 Aug 01/05 CES

 

 THS Mechanical Control R Figure 201/TASK 27-40-00-991-001
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-40-00∞∞∞∞∞∞∞∞∞∞Page 218
 Aug 01/05 CES

 

R - if you find stiffness, go to Para. (d).

R  (d) Do a check for a failure of the mechanical part of the pitch-trim 
R  control mechanism (6) and the stop and gearset unit (5): 
R  1_  Do this corrective action:
R  - replace the pitch-trim control mechanism (Ref. AMM TASK 27-
R  41-41-000-001) and (Ref. AMM TASK 27-41-41-400-001). 
R  or 
R  - replace the pitch trim control stop and gearset unit (Ref. 
R  AMM TASK 27-41-43-000-001) and (Ref. AMM TASK 27-41-43-400-
R  001). 
R  2_  Connect the shaft (4) to the stop and gearset unit (5):
R  - install the tapered pin (12). 
R  - remove the standard locking bolt (10). 
R  - remove the trim-control lower shaft holding-tool. 
R  3_  Connect the shaft (2) to the THS actuator (1):
R  - connect the mechanical system link-plate (7) to the input 
R  lever (9). 
R  - remove the THS-actuator mechanical input lever rigging-pin 
R  (8). 
R  4_  Go to the Para. (g).
R  (e) Check of the cable tension regulator: 
R  - do a visual inspection of the cable tension regulator (3): 
R  1_  Make sure that the cables are correctly installed in the
R  pulleys. 
R  2_  Make sure that the rigging scale index is in the correct
R  position on the cable tension regulator. 
R  3_  Do a check of the cable tension regulator of the THS trim
R  control (Ref. AMM TASK 27-41-00-220-001): 
R  - if OK, go to Para. (f). 
R  - if not OK, do this corrective action: 
R  a_  Replace the cable tension regulator (Ref. AMM TASK 27-41-
R  42-000-001) and (Ref. AMM TASK 27-41-42-400-001). 
R  b_  Connect the shaft (2) to the THS actuator (1):
R  - connect the mechanical system link-plate (7) to the input 
R  lever (9). 
R  - remove the mechanical input lever rigging-pin (8). 
R  c_ Go to the Para. (g).

 

R  (f) Check of the THS mechanical control: 
R  - do a visual inspection of the THS mechanical control (Ref. AMM 
R  TASK 27-41-00-210-003), (Ref. AMM TASK 27-41-00-210-002), (Ref. 
R  AMM TASK 27-41-00-210-001). 
R  1_  Remove the THS control cables (Ref. AMM TASK 27-41-44-000-
R  001). 
R  2_  Do a check of the bearings of the shafts (2) and (4).
R  3_  Install the THS control cables (Ref. AMM TASK 27-41-44-400-
R  001). 
R  4_  Connect the shaft (4) to the stop and gearset unit (5):
R  - install the tapered pin (12). 
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 飛行操縱 1(78)