- refer to Para. Fault Isolation.
(b) If the ground scanning gives at least two maintenance messages of the list below: SEC1 OR WIRING FROM L ELEV POS MON XDCR SEC1 OR WIRING FROM R ELEV POS MON XDCR SEC1 MON OR WIRING FROM THS ACTR XDCR2 9CE SEC1 OR WIRING FROM L G ELEV MODE XDCR 34CE1 SEC1 OR WIRING FROM R Y ELEV MODE XDCR 34CE2
- do this trouble shooting procedure (Ref. TASK 27-90-00-810-818).
4. Fault Isolation
_______________
A. If the BITE test gives the maintenance message:
SEC1 MON OR WIRING FROM THS ACTR XDCR2 9CE
(1) On the overhead panel 23VU:
- make sure that the FLT CTL/ELAC1 pushbutton switch is pushed (the FAULT and OFF legends of this pushbutton switch are off).
- release the FLT CTL/SEC1 pushbutton switch (the OFF legend of this pushbutton switche comes on).
(2) On the overhead panel 24VU:
- release the FLT CTL/ELAC2, FLT CTL/SEC2 and the FLT CTL/SEC3 pushbutton switches (the OFF legend of these pushbutton switches comes on).
(3) Pressurize the aircraft hydraulic systems (Ref. AMM TASK 29-23-00-864-001) (Ref. AMM TASK 29-24-00-864-001), (Ref. AMM TASK 29-10-00-864-003).
(4) Do the BITE test of the EFCS (Groud Scanning) (Ref. AMM TASK 27-96-00-740-001).
(a) If the ground scanning gives a maintenance message related to the ELAC1 and THS ACTR XDCR:
- replace the monitor position transducer of the THS actuator (Ref. AMM TASK 27-44-56-400-001), (Ref. AMM TASK 27-44-56-400-001)
- If the fault continues:
- replace the command position transducer of the THS actuator (Ref. AMM TASK 27-44-56-400-001), (Ref. AMM TASK 27-44-56-400-001).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-94-00∞∞∞∞∞∞∞∞∞∞Page 270
Feb 01/03R CES
1_ If the fault continues:
- do a check of the wiring of the XDCR COM from the THS
actuator (9CE) to the first terminal block (Ref. ASM 27-
93/12).
2_ If the fault continues:
- do a check of the wiring of the XDCR MON from the THS
actuator (9CE) to the first terminal block (Ref. ASM 27-
93/12).
(b) If the ground scanning does not give a maintenance message related to the ELAC1 and THS ACTR XDCR:
- replace the SEC-1 (1CE1), (Ref. AMM TASK 27-94-34-000-001) and (Ref. AMM TASK 27-94-34-400-001).
(5) If the fault continues:
- do a check and repair the wiring from the ANI 2-3 XDCR MON signal of the SEC 1 (1CE1) to the first terminal block, (Ref. ASM 27-94/12).
B. Do the tests given in Para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-94-00∞∞∞∞∞∞∞∞∞∞Page 271
Feb 01/03R
CES Loss of the Servo Motor 2 Signal on the THS Actuator for the SEC 1
1. Possible Causes
_______________
- SEC-1 (1CE1)
- wiring of the K12-1 and 2 signal from the SEC 1 (1CE1) to the SEC 1 (1CE1)
- wiring of the K12-1B and 2B signal from the SEC 1 (1CE1) to the first terminal block
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 27-94-34-000-001 Removal of the SEC (1CE1,1CE2,1CE3)
AMM 27-94-34-400-001 Installation of the SEC (1CE1,1CE2,1CE3)
AMM 27-96-00-710-022 Operational Test of the THS Actuator Electrical
Control (Activation for BITE Test)
AMM 27-96-00-740-001 BITE Test of the EFCS (Ground Scanning)
ASM 27-94/12
3. Fault Confirmation
__________________
A. Test
(1) Do the operational test of the THS actuator electrical control (Ref. AMM TASK 27-96-00-710-022).
NOTE : Do the ground setting only with the SEC 1.
____
(2) Do the BITE test of the EFCS (Ground Scanning) (Ref. AMM TASK 27-96-00-740-001).
4. Fault Isolation
_______________
A. If the BITE test gives the maintenance message:
SEC1 OR WIRING TO THS ACTR SERVO MOT2 9CE
- replace the SEC-1 (1CE1), (Ref. AMM TASK 27-94-34-000-001) and (Ref. AMM TASK 27-94-34-400-001).
(1) If the fault continues:
- do a check of the wiring of the K12-1 and 2 signal from the SEC 1 (1CE1) to the SEC 1 (1CE1), (Ref. ASM 27-94/12).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 飛行操縱 3(108)
