(Activation for the BITE Test)
 AMM 27-96-00-740-001 BITE Test of the EFCS (Ground Scanning)
 ASM 27-93/08

 3. Fault Confirmation
__________________
 A. Test
 (1) Do the operational test of the side stick assembly (activation for the BITE test) (Ref. AMM TASK 27-96-00-710-020).

 (2) Do the BITE test of the EFCS (ground scanning) (Ref. AMM TASK 27-96-00-740-001).

 (a) If the ground scanning gives the maintenance message: ELAC2 OR WIRING FROM R Y ELEV POS XDCR 34CE2

 - refer to Para. Fault Isolation.

 (b) If the ground scanning gives at least two maintenance messages of the two lists below: First list:

 - ELAC2 COM OR INPUT OF THS ACTR XDCR1 9CE

 - ELAC2 OR WIRING FROM L G ELEV POS XDCR 34CE1

 - ELAC2 OR WIRING FROM R Y ELEV POS XDCR 34CE2 Second list:

 - ELAC2 MON OR INPUT OF THS ACTR XDCR1 9CE

 - ELAC2 OR WIRING FROM L ELEV POS MON XDCR

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-93-00∞∞∞∞∞∞∞∞∞∞Page A266
 Feb 01/03R CES

 - ELAC2 OR WIRING FROM R ELEV POS MON XDCR

 - ELAC2 OR WIRING FROM L B ELEV MODE XDCR 34CE3

 - ELAC2 OR WIRING FROM R Y ELEV MODE XDCR 34CE4

 1_ First case:
 Combination of maintenance messages of the first list, do this
 trouble shooting procedure (Ref. TASK 27-90-00-810-814).
 2_ Second case:
 Combination of maintenance messages of the second list, do
 this trouble shooting procedure (Ref. TASK 27-90-00-810-815).
 3_ Third case:
 Combination of maintenance messages of the first and second
 lists, do this trouble shooting procedure (Ref. TASK 27-90-00-
810-816).

 4. Fault Isolation
_______________
 A. If the test gives the maintenance message: ELAC2 OR WIRING FROM R Y ELEV POS XDCR 34CE2
 - replace the ELAC-2 (2CE2) (Ref. AMM TASK 27-93-34-000-001) and (Ref. AMM TASK 27-93-34-400-001).
 (1) If the fault continues:
 - do a check and repair the wiring of the POS XDCR COM (ANI 2-2) signal from the ELAC 2 (2CE2) to the first terminal block (Ref. ASM 27-93/08).
 B. Do the tests given in Para. 3.
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-93-00∞∞∞∞∞∞∞∞∞∞Page A267
 Feb 01/03R
 CES  Loss of the Signal of the Right Elevator Position Transducer (MON) by the ELAC

 1. Possible Causes
_______________
 - ELAC-2 (2CE2)

 - wiring of the POS RVDT MON (ANI 2-2) signal from the ELAC 2 (2CE2) MON part to the first terminal block

 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-90-00-810-814 Loss of the ACS1 Signal of the ELAC2 COM Side
 27-90-00-810-815 Loss of the ACS1 Signal of the ELAC2 MON Side
 27-90-00-810-816 Loss of the ACS1 of the ELAC2 COM and MON Sides
 AMM 27-93-34-000-001 Removal of the ELAC (2CE1,2CE2)
 AMM 27-93-34-400-001 Installation of the ELAC (2CE1,2CE2)
 AMM 27-96-00-710-020 Operational Test of the Side Stick Assembly

 (Activation for the BITE Test)
 AMM 27-96-00-740-001 BITE Test of the EFCS (Ground Scanning)
 ASM 27-93/08

 3. Fault Confirmation
__________________
 A. Test
 (1) Do the operational test of the side stick assembly (activation for the BITE test) (Ref. AMM TASK 27-96-00-710-020).

 (2) Do the BITE test of the EFCS (ground scanning) (Ref. AMM TASK 27-96-00-740-001).

 (a) If the ground scanning gives the maintenance message: ELAC2 OR WIRING FROM R ELEV POS MON XDCR

 - refer to Para. Fault Isolation.

 (b) If the ground scanning gives at least two maintenance messages of the two lists below: First list:

 - ELAC2 COM OR INPUT OF THS ACTR XDCR1 9CE

 - ELAC2 OR WIRING FROM L G ELEV POS XDCR 34CE1

 - ELAC2 OR WIRING FROM R Y ELEV POS XDCR 34CE2 Second list:

 - ELAC2 MON OR INPUT OF THS ACTR XDCR1 9CE

 - ELAC2 OR WIRING FROM L ELEV POS MON XDCR

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-93-00∞∞∞∞∞∞∞∞∞∞Page A268
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 飛行操縱 3(43)