_
- repair it
- install the ELAC2 (Ref. AMM TASK 27-93-34-400-001) 4 do a check of the wiring from the ELAC2 (2CE2) COM part to the
_ ELAC2 MON part, from the pin AB/12E to the pin AE/10D (Ref. ASM 27-93/08):
a If the wiring is correct, see Para. 5_
_
b If the wiring is not correct:
_
- repair it
- install the ELAC2 (Ref. AMM TASK 27-93-34-400-001) 5 do a check and repair the wiring from the ELAC2 (2CE2) MON
_ part pins AE/13A and AE/10C to the first terminal block (Ref. ASM 27-93/08):
6 Install the ELAC-2 (2CE2) (Ref. AMM TASK 27-93-34-400-001).
_
(b) If the resistance is less than 100 Megohms:
- at the SERVO CTL-L ELEVATOR, OUTBD B (34CE3), do a check of the insulation of the solenoid valve between pin C/K (pin C/L) and the ground.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-93-00∞∞∞∞∞∞∞∞∞∞Page A227
Feb 01/03R CES
1_ If the resistance is less than 100 Megohms:
- replace the solenoid valve (Ref. AMM TASK 27-34-51-000-005)
and (Ref. AMM TASK 27-34-51-400-004).
a Do again a check of the insulation of the solenoid valve
_ between pin C/K (pin C/L) and the ground. If the resistance is less than 100 Megohms: . Replace the SERVO CTL-L ELEVATOR, OUTBD B (34CE3) (Ref. AMM TASK 27-34-51-000-001) and (Ref. AMM TASK 27-34-51-400-001). . Replace the ELAC-2 (2CE2) (Ref. AMM TASK 27-93-34-000-001) and (Ref. AMM TASK 27-93-34-400-001).
2 If the resistance is more than 100 Megohms:
_
a Repair the wiring of the solenoid valve signal from the
_ SERVO CTL-L ELEVATOR, OUTBD B (34CE3) to the ELAC-2 (2CE2)
b Replace the ELAC-2 (2CE2).
_
B. Do the test given in Para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-93-00∞∞∞∞∞∞∞∞∞∞Page A228
Feb 01/03R
CES Loss of the Signal of the Left Green Elevator-Servocontrol Position-Transducer by the ELAC 2
1. Possible Causes
_______________
- ELAC-2 (2CE2)
- wiring of the POS RVDT COM (ANI 2-1) signal from the ELAC 2 (2CE2) to the first terminal block
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-90-00-810-814 Loss of the ACS1 Signal of the ELAC2 COM Side
27-90-00-810-815 Loss of the ACS1 Signal of the ELAC2 MON Side
27-90-00-810-816 Loss of the ACS1 of the ELAC2 COM and MON Sides
AMM 27-93-34-000-001 Removal of the ELAC (2CE1,2CE2)
AMM 27-93-34-400-001 Installation of the ELAC (2CE1,2CE2)
AMM 27-96-00-710-020 Operational Test of the Side Stick Assembly
(Activation for the BITE Test)
AMM 27-96-00-740-001 BITE Test of the EFCS (Ground Scanning)
ASM 27-93/08
3. Fault Confirmation
__________________
A. Test
(1) Do the operational test of the side stick assembly (activation for the BITE test) (Ref. AMM TASK 27-96-00-710-020).
(2) Do the BITE test of the EFCS (ground scanning) (Ref. AMM TASK 27-96-00-740-001).
(a) If the ground scanning gives the maintenance message: ELAC2 OR WIRING FROM L G ELEV POS XDCR 34CE1
- refer to Para. Fault Isolation.
(b) If the ground scanning gives at least two maintenance messages of the two lists below: First list:
- ELAC2 COM OR INPUT OF THS ACTR XDCR1 9CE
- ELAC2 OR WIRING FROM L G ELEV POS XDCR 34CE1
- ELAC2 OR WIRING FROM R Y ELEV POS XDCR 34CE2 Second list:
- ELAC2 MON OR INPUT OF THS ACTR XDCR1 9CE
- ELAC2 OR WIRING FROM L ELEV POS MON XDCR
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-93-00∞∞∞∞∞∞∞∞∞∞Page A229
Feb 01/03R CES
- ELAC2 OR WIRING FROM R ELEV POS MON XDCR
- ELAC2 OR WIRING FROM L B ELEV MODE XDCR 34CE3
- ELAC2 OR WIRING FROM R Y ELEV MODE XDCR 34CE4 中國航空網(wǎng) www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 飛行操縱 3(28)
