F 『
E C F M E
E E
E 56 E
E E
(a) If the resistance values are in the specified limits:
- replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
(b) If the resistance values are out of the specified limits: R - disconnect the harness J8 from the fuel return valve. R - do a visual inspection of the harness connector and receptacle. R Look for contamination or oxidation or pins that have damage. R - if you find damage, repair or replace as required. R - clean the connector and receptacle with a bristle brush and R stoddard solvent (Material No. CP2011) (Ref. AMM TASK 73-21-50-R 210-002). R - do a resistance check between: R
. pins 1 and 2 (18 to 38 ohms) . pin 1 and the ground (> 10 megohms)
1 If the resistance values are out of the specified limits:
_
- replace the fuel return valve (Ref. AMM TASK 73-11-50-000-002) and (Ref. AMM TASK 73-11-50-400-002).
2 If the resistance values are in the specified limits:
_
- replace the harness J8 (Ref. AMM TASK 73-21-50-000-041) and (Ref. AMM TASK 73-21-50-400-041).
B. Do the test given in Para. 3.A.
F 『 EEFF : ALL E ∞∞73-20-00∞∞∞∞∞∞∞∞∞∞Page A214
E E Aug 01/05 E E ECES
E
F 『
E C F M E
E E
E 56 E
E E
TASK 73-20-00-810-909
Failure of the Control of the Solenoid 2 of the Fuel Return Valve on Channel A, Engine 1
1. Possible Causes
_______________
- ECU (4000KS)
- fuel return valve
- harness J7
2. Job Set-up Information
______________________
R A. Fixtures, Tools, Test and Support Equipment
R -------------------------------------------------------------------------------R REFERENCE QTY DESIGNATION
R -------------------------------------------------------------------------------
R No specific bristle brush
R B. Consumable Materials
R -------------------------------------------------------------------------------R REFERENCE DESIGNATION
R -------------------------------------------------------------------------------
R Material No. CP2011 *
R stoddard solvent (Ref. 70-30-00)
R C. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
R AMM AMM AMM AMM AMM AMM AMM 73-11-50-000-002 73-11-50-400-002 73-21-50-000-040 73-21-50-210-002 73-21-50-400-040 73-21-60-000-001 73-21-60-400-001
AMM 73-29-00-710-040
ASM 78-25/18
F EEFF : ALL E E ECES Removal of the Fuel Return Valve (FRV)Installation of the Fuel Return ValveRemoval of the HJ7 Harness Visual Inspection of the Wiring HarnessesInstallation of the HJ7 HarnessRemoval of the Electronic Control Unit (ECU)(4000KS)Installation of the Electronic Control Unit (ECU)(4000KS)Operational Test of the FADEC on the Ground (with Engine non Motoring)
『E
∞∞73-20-00∞∞∞∞∞∞∞∞∞∞Page A215
E Aug 01/05EE
F 『
E C F M E
E E
E 56 E
E E
3. Fault Confirmation
__________________
A. Test
(1) Do the operational test of the FADEC 1A on the ground (with engine non-motoring) (Ref. AMM TASK 73-29-00-710-040).
4. Fault Isolation
_______________
A. The fault is generated when the ECU detects an open circuit or a short to ground on the fuel return valve solenoid for second level cooling or on associated electrical harness.
(1) If the test does not give the maintenance message J7, FRV(SOL 2), ECU or if the fault is repetitive:
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 發動機燃油和控制 1(110)
